SCREAMIN' EAGLE MILWAUKEE-EIGHT 135 CRATE ENGINE
941004462024-01-23
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
16200759, 16200760, 16200767, 16200937 | Safety Glasses, Torque Wrench, Digital Technician II (DT II), H-D Special Tools |  |
(1) DTII and dealer installation required
KIT CONTENTS
Figure 1. Screamin' Eagle Milwaukee-Eight 135 Crate Engine
Table 2. Screamin' Eagle Milwaukee-Eight 135 Crate Engine
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Engine assembly | 16200759, 16200760, 16200767, 16200937 | |
| 2 | 1 | Screamin Eagle High-Flow Injector Kit | 27400067 | |
| 3 | 1 | Screamin Eagle 68mm Throttle Body Kit | 27300194 | |
| 4 | 1 | 68mm CNC Ported Intake Manifold | 27300217 | |
Figure 2. Screamin' Eagle Milwaukee-Eight 135 Cylinder Heads
Table 3. Screamin' Eagle Milwaukee-Eight 135 Cylinder Heads
| Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
| 1 | 2 | Automatic compression release | 18400073B | |
| 2 | 8 | Flange nut | 10200303 | |
| 3 | 16 | Keeper, valve | Not sold separately | |
| 4 | 8 | Collar, valve spring | Not sold separately | |
| 5 | 8 | Valve spring | Not sold separately | |
| 6 | 8 | Seal, valve | Not sold separately | |
| 7 | 1 | Cylinder head assembly, rear, black granite | 16501088 | |
| 1 | Cylinder head assembly, front, black granite | 16501086 | ||
| 1 | Cylinder head assembly, rear, black | 16501087 | ||
| 1 | Cylinder head assembly, front, black | 16501085 | ||
| 8 | 2 | Exhaust valve, 34 mm | 18000057 | |
| 9 | 2 | Intake valve, 42 mm | 18000056 | |
| 10 | 4 | Screw, button head, TORX | 68120-00 | |
| 11 | 2 | Medallion, 135 | 14102009 | |
| 12 | 4 | Stud, exhaust port | 10900015A | |
Items mentioned, but not included in kit | |||||
| A | Valve spring kit, Screamin' Eagle | 18100080 | ||
Figure 3. Screamin' Eagle Milwaukee-Eight 135 Pistons
Table 4. Screamin' Eagle Milwaukee-Eight 135 Pistons
| Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
| 1 | 1 | Piston kit, front and rear (Includes items 2-4) | 21900164A | |
| 2 | 2 | Piston ring set, standard | 22000126 | |
| 3 | 4 | Lock ring, piston pin | 22097-99 | |
| 4 | 2 | Piston pin | 22310-10 | |
Figure 4. Screamin' Eagle Milwaukee-Eight 135 Cylinders
Table 5. Screamin' Eagle Milwaukee-Eight 135 Cylinders
| Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
| 1 | 2 | Screamin Eagle Cylinder Kit, 4.310 in., front and rear cylinders, black granite (Includes items 2-4) | 16800404 | |
| 2 | Screamin Eagle Cylinder Kit, 4.310 in., front and rear cylinders, black (Includes items 2-4) | 16800407 | ||
| 2 | 4 | Dowel pin, ring | 16589-99A | |
| 3 | 2 | Gasket, cylinder base | 16500332A | |
| 4 | 2 | Gasket, cylinder base | 16500657A | |
Figure 5. Screamin' Eagle Milwaukee-Eight 135 Camshaft Chest Components
Table 6. Screamin' Eagle Milwaukee-Eight 135 Camshaft Chest Components
| Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
| 1 | 1 | Camshaft kit, SE8-550 | 25400432 | |
| 2 | 1 | Needle bearing kit, camshaft | 24018-10 | |
| 3 | 1 | Oil pump assembly | 92400278 | |
| 4 | 1 | Spring, relief valve | 26210-99 | |
| 5 | 1 | Relief valve, oil pump bypass | 26400-82B | |
| 6 | 1 | Roll pin | 601 | |
| 7 | 1 | O-ring | 11293 | |
| 8 | 4 | Hydraulic lifters | 18572-13 | |
| 9 | 1 | O-ring | 11900103 | |
| 10 | 1 | Camshaft plate assembly | 25400419 | |
| 11 | 1 | Retention kit | 25566-06 | |
| 12 | 1 | Gasket, camshaft cover | 25700370 | |
| 13 | 1 | Medallion, 135, Stage IV | 14102009 | |
| 14 | 1 | Gasket kit | 25700731 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
- Kit requires Electronic Control Module (ECM) recalibration. Contact a Harley-Davidson dealership.
- Separate purchase of Exhaust Header (Part No. 65600177) maybe required to maintain compliance. See a Harley-Davidson dealer.
- 10-plate assist and slip clutch used in Milwaukee-eight vehicles has sufficient capacity to support this kit for most applications. Only install higher capacity springs if clutch slippage occurs. Higher capacity springs will increase clutch lever effort.
These items are available at your local Harley-Davidson dealership.
PREPARE
| 1. | Set motorcycle upright. See service manual. | |
| 2. | Disarm security system. See service manual. | |
| 3. | Remove seat. See service manual. | |
| 4. | Remove main fuse. See service manual. | |
| 5. | Remove fuel tank. See service manual. | |
| 6. | Liquid-Cooled Cylinder Heads with Center Position Radiator: Drain coolant system. See service manual. |
REMOVE
| 1. | Remove engine from chassis. See the ENGINE section of service manual. |
INSTALL
| 1. | Before installing the engine, make sure that there is no debris or contaminates in the oiling system. Have the oil pan flushed out by a Harley-Davidson dealer or qualified technician. If the engine that was removed had internal damage, replace oil pan. | |
| 2. | Remove the oil passage caps or plugs at the engine to transmission interface. | |
| 3. | Install the engine to the chassis. See the ENGINE section of the service manual. | |
| 4. | Install throttle body and high flow injectors following instructions in this kit. |
COMPLETE
NOTE
For the latest coolant bleeding procedure and required tools, reference the electronic version of the service manual in Refer to: https://serviceinfo.harley-davidson.com.
The initial printed 2023 CVO service manual for the Street Glide (FLHXSE) and Road Glide (FLTRXSE) may not have the current information.
| 1. | Liquid-Cooled Cylinder Heads with Center Position Radiator: Service coolant system. See service manual. | |
| 2. | Install fuel tank. See service manual. | |
| 3. | Install main fuse. See service manual. | |
| 4. | Install seat. After installing seat, pull up on the seat to verify that it is secure. See service manual. | |
| 5. | Calibrate ECM with proper calibration for configuration. See dealer for details. | |
| 6. | Run motorcycle until engine is at normal operating temperature. Repeat several times to verify proper operation. |
OPERATION
See owner's manual for BREAK-IN RIDING RULES.
MAINTENANCE
| 1. | Refer to the MAINTENANCE SCHEDULE in the vehicle service manual or owner's manual. | |
| 2. | Refer to ENGINE section of service manual for proper service procedures. |
135 ENGINE SPECIFCATIONS
NOTE
The following sections provide unique information not available in the Touring service manual ENGINE section for the Milwaukee-Eight engine.
Table 7. Engine: Screamin' Eagle Milwaukee-Eight 135
Item | Specification | |
|---|---|---|
Compression Ratio | 11.7:1 | |
Bore | 4.310 in | 109.5 mm |
Stroke | 4.625 in | 117.5 mm |
Displacement | 135 cu in | 2212 cc |
Lubrication system | Pressurized dry sump with oil cooler | |
MANUFACTURING TOLERANCES
Refer to the engine specifications in the service manual for any specification not shown in the following tables.
Table 8. Valve Spring Specifications
ITEM | PRESSURE | DIMENSION |
|---|---|---|
Height 1 | 100 lbs (45 kg) | 1.470 in. (37.4 mm) |
Height 2 | 262 lbs (119 kg) | 0.97 in. (24.6 mm) |
Free length | n/a | 1.779 in. (45.2 mm) |
Table 9. Pistons
Piston: | Clearance (in.) |
|---|---|
Piston-to-cylinder fit (Loose) | 0.0045 |
Piston pin fit (Loose) | 0.0002-0.0005 |
Top Ring End Gap Second Ring End Gap Oil Control Ring Rail Gap | 0.015-0.025 0.015-0.025 0.015±0.009 |
Top Ring Side Clearance Second Ring Side Clearance Oil Control Ring Side Clearance | 0.0017-0.0027 0.0009-0.0029 0.0004-0.0059 |
Table 10. Camshaft Specifications-SE8-550
Intake | Specification |
|---|---|
Opens | F-9.4° B; R-6.4° B |
Closes | F-41.4° A; R-40°A |
Duration | F-230.8°; R-226.8° |
Maximum Valve Lift | I -552 in. |
Valve Lift @ TDC | F-.116 in.; R-.102 in. |
Exhaust | Specification |
Opens | F-69.4° BBDC: R-68.4°BBDC |
Closes | F-5.8° A; R-2.8° A |
Duration | F-255.2°; R-251.2° |
Maximum Valve Lift | 0.551 in. |
Valve Lift @ TDC | F-0.102 in.; R-0.091 in. |
Cam Timing @ 0.050 in. Tappet Lift in Crankshaft Degrees | |
SERVICE WEAR LIMITS
NOTE
Refer to the engine specifications in the service manual for any specification not shown in the following tables.
Use wear limits as guide to part replacement.
Table 11. Pistons
Piston-to-cylinder fit (Loose) | Wear Limit (in.) |
|---|---|
Fit in cylinder (Loose) | 0.0045 |
Piston Pin Fit (Loose) | 0.0010 |
Top Ring End Gap Second Ring End Gap Oil Control Ring Rail Gap | 0.030 0.034 0.038 |
Top Ring Side Clearance Second Ring Side Clearance Oil Control Ring Side Clearance | 0.0035 0.0035 0.0067 |