STAGE III SPEAKER KIT SADDLEBAG LID (PN76001231)
941004832024-12-13
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
76001231 | Safety Glasses, Torque Wrench, Screwdriver |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Stage III Speaker Kit Saddlebag Lid
Table 2. Kit Contents: Stage III Speaker Kit Saddlebag Lid
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Saddlebag speaker, 6x9, left | 76001182 | |
| 2 | 1 | Saddlebag speaker, 6x9, right | 76001134 | |
| 3 | 2 | Label, warning capacity | 14003811 | |
GENERAL
NOTE
The various generations of speakers, amplifiers and wiring for Harley-Davidson vehicles were not designed or tested to work together. Consult your dealership to ensure optimal performance and compatibility.
Models
NOTE
These speakers are for use ONLY on 2023½ FLHXSE and FLTRXSE models.
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
Installation by a technician at a Harley-Davidson dealership is recommended.
To ensure proper audio performance, Digital Technician II (DT II) is required for audio configuration and amplifier firmware update.
PREPARE
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
| 1. | Remove left saddlebag. See service manual. | |
| 2. | Remove left side cover. See service manual. NOTE Models with security: Disable security system. | |
| 3. | Remove main fuse. See service manual. |
REMOVE
NOTE
New speaker components are shown in graphic, Original Equipment Manufacturer (OEM) is similar.
| 1. | Disconnect OEM audio harness connectors. | |
| 2. | Figure 2 Remove grille screws (4). | |
| 3. | Remove OEM speaker grille (1). | |
| 4. | Remove speaker screws (5). | |
| 5. | Remove OEM speaker (2) from saddlebag lid. | |
| 6. | Repeat procedure for opposite side. |
INSTALL
| 1. | Figure 1 Install speaker (1, 2) into saddlebag lid. a. Figure 2 Orient speaker to saddlebag lid. | |
| 2. | Figure 2 Install speaker screws (4). a. Alternately tighten screws. b. Tighten. Torque: 2–2.5 N·m (17.7–22.1 in-lbs) Speaker screw | |
| 3. | Make sure spacers (3) are properly seated in saddlebag lid. | |
| 4. | Install speaker grille (1) to saddlebag lid. | |
| 5. | Install grille screws (4). a. Alternately tighten screws. b. Tighten. Torque: 2–2.5 N·m (17.7–22.1 in-lbs) Speaker screw | |
| 6. | Connect OEM audio harness connectors. | |
| 7. | Figure 1 Install saddlebag capacity label (3). a. Apply over current label. | |
| 8. | Repeat procedure for opposite side. |
| 1 | Grille |
| 2 | Speaker |
| 3 | Spacer (4) |
| 4 | Grille screw (4) |
| 5 | Speaker screw (4) |
Figure 2. Speaker and Grille Assembly (Typical)
COMPLETE
NOTE
To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.
| 1. | Install main fuse. See service manual. | |
| 2. | Turn the ignition ON, but do not start the motorcycle. | |
| 3. | Make sure that all speakers are working and front/rear fader function is operating correctly. If not, check speaker wiring. a. To ensure proper audio performance, DT II is required for audio configuration and amplifier firmware update. | |
| 4. | Install left side cover. See service manual. | |
| 5. | Install left saddlebag. See service manual. |
SUPPLEMENTAL PROCEDURE VIDEO
WARNINGAlways review the appropriate service procedure prior to performing it. This video is intended to supplement, not replace, documented service procedures. Attempting service procedures without the proper training, tools, equipment, and manuals could result in death or injury to you or others. This could also damage the motorcycle or cause the motorcycle to operate improperly. (10406a)
This video is a supplement of the procedure covered in the document. This video can only be viewed through Service Information Portal (SIP).
Video 1.