0/0
SCREAMIN' EAGLE REMOTE RESERVOIR REAR SHOCKS (OHLINS®)
941005532025-02-28
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
54000350, 54000351
Safety Glasses, Torque Wrench
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Screamin' Eagle Remote Reservoir Rear Shocks (Ohlins)
Table 2. Kit Contents: Screamin' Eagle Remote Reservoir Rear Shocks (Ohlins)
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
2
Clamp bracket
Not sold separately
Included in Shock Bracket service kit (Part No. 54000354)
2
4
Screw, short head
3832M
3
2
Mounting bracket
Not sold separately
Included in Shock Bracket service kit (Part No. 54000354)
4
4
Screw, long
10200850
5
4
Spacer, short
54000298
6
4
Spacer, long
54000297
7
2
Screw, flat head
10201180
8
2
Shock with reservoir, gold finish
54000360
Shock with reservoir, black finish
54000375
9
4
Washer (4)
6590HW
GENERAL
Instruction sheet is also available electronically. To verify you are using the most current version available, do one of the following:
  • Go to h-d.com/isheets
  • Scan QR code in upper left corner of the instruction sheet
NOTE
This instruction sheet may have a Supplemental Video to assist installer in clarifying a certain part of the assembly. A linked video would be located at the end of this instruction sheet.
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
PREPARE
1. Set vehicle upright. See service manual.
a. Secure with tie-downs.
2. Raise rear of vehicle. See service manual.
3. Remove saddlebags. See service manual.
REMOVE
1. Remove OE rear shocks absorbers. See service manual.
a. Save screws and washers for later use.
2. See Figure 2. Remove OE screws (2) from fender strut (1).
1Fender strut
2OE Screw (2)
Figure 2. Fender Strut Screws
INSTALL
1. See Figure 3. Install appropriate spacers (2) into mounting bracket (3). Tighten.
Torque: 11 N·m (8 ft-lbs) Mounting bracket spacer
NOTE
See Figure 4. For spacer selection, reference the accessory that is used on the vehicle.
a. Short Spacer: Use with Tour Pak (1) or saddlebag support insert (2). Other accessory inserts can be used like the 4-Point Docking Hardware Kit.
b. Long Spacer: Use with fender strut insert (3).
c. See Figure 3. Apply thread locker to mounting spacers (2).LOCTITE 262 HIGH STRENGTH THREADLOCKER AND SEALANT (RED) (94759-99)
2. See Figure 3. Apply thread locker to screw (4).LOCTITE 262 HIGH STRENGTH THREADLOCKER AND SEALANT (RED) (94759-99)
3. Install mounting bracket (3).
a. Install screws (4). Tighten.
Torque: 27 N·m (20 ft-lbs)
4. See Figure 5. Install shock assembly.
NOTE
Reuse original OE mounting hardware. See service manual or reference parts catalog for model year of vehicle.
a. Install OE mounting hardware (3).
b. Install screw (3) to shock assembly (4).
c. Install inner washer (2).
d. Install screw (3) to frame. Do not tighten completely.
e. Repeat procedure for other screw.
f. Tighten screws (3). See service manual.
5. Install reservoir (1) in clamp bracket.
a. Adjust as needed for proper hose routing.
6. See Figure 3. Install clamp bracket (1) to mounting bracket (3).
a. Install screws (5). Tighten.
Torque: 7 N·m (62 in-lbs)
7. See Figure 6. Adjust reservoir (1) and install screw (2). Tighten.
Torque: 3 N·m (27 in-lbs)
1Clamp bracket
2Spacer
3Mounting bracket
4Screw, short
5Screw, long
Figure 3. Mounting Brackets
1Tour-Pak support
2Saddlebag support insert
3Fender strut insert
4Fender strut
Figure 4. Spacer Accessories Selection
1Reservoir
2Washer (2)
3OE Mounting hardware (2)
4Shock assembly (with reservoir)
Figure 5. Shock Assembly
1Reservoir
2Screw, flat head
Figure 6. Clamp Bracket Screw
COMPLETE
NOTE
Ohlins shocks are pre-set at Harley-Davidson's original equipment length.
Adjusting length could result in tire and fender contact or axle and muffler contact at travel limits on some vehicles.
1. Reference Ohlins owner's manual for: Setting up, adjustments, spring preload, compression damping, rebound damping adjust length and general setup.
2. Install saddlebags. See service manual.
Table 3.
Rear Shocks
Compression1
Rebound1
Without Tourpak
Solo rider
15
18
Solo rider
with luggage
13
16
Solo rider
with passenger
8
10
Solo rider
with luggage
and passenger
7
9
With Tourpak
Solo rider
13
15
Solo rider
with luggage
8
10
Solo rider
with passenger
6
8
Solo rider
with luggage
and passenger
5
7
1 Damping adjuster settings are done by tightening adjuster clockwise until it stops and then turning the adjuster counter clockwise to the first click (this is position 1), then count clicks while turing adjuster counter-clockwise to the desired setting.
Table 4.
Suspension Preload Table
Without Tourpak - Additional Weight of Passenger, Cargo and Accessories
LB
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
KG
0
5
9
14
18
23
27
32
36
41
45
50
54
59
64
68
73
77
82
87
92
97
With Tourpak - Additional Weight of Passenger, Cargo and Accessories
LB
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
KG
0
5
9
14
18
23
27
32
36
41
45
50
54
59
64
68
73
RIDER WEIGHT
Measurement Reading
Top of Spring Preload Adjuster (2) to Bottom of Shock Upper Body (1)
Measurement Reading (3) in Millimeters (mm)
LB
KG
150
68
11
12
13
14
14
15
16
17
18
18
19
20
21
21
22
23
24
25
25
26
27
28
160
73
12
13
14
14
15
16
17
17
18
19
20
20
21
22
23
24
24
25
26
27
27
28
170
77
13
13
14
15
16
16
17
18
19
19
20
21
22
23
23
24
25
26
26
27
28
29
180
82
13
14
15
15
16
17
18
19
19
20
21
22
22
23
24
25
25
26
27
28
29
29
190
86
14
14
15
16
17
18
18
19
20
21
21
22
23
24
25
25
26
27
28
28
29
30
200
91
14
15
16
17
17
18
19
20
20
21
22
23
24
24
25
26
27
27
28
29
30
31
210
95
15
16
16
17
18
19
20
20
21
22
23
23
24
25
26
26
27
28
29
30
30
31
220
100
15
16
17
18
19
19
20
21
22
22
23
24
25
26
26
27
28
29
29
30
31
32
230
104
16
17
18
18
19
20
21
21
22
23
24
25
25
26
27
28
28
29
30
31
31
32.3
240
109
17
17
18
19
20
20
21
22
23
24
24
25
26
27
27
28
29
30
31
31
32.5
32.5
250
113
17
18
19
20
20
21
22
23
23
24
25
26
26
27
28
29
30
30
31
32
32.5
32.5
260
118
18
19
19
20
21
22
22
23
24
25
26
26
27
28
29
29
30
31
32
32.5
32.5
32.5
270
122
18
19
20
21
21
22
23
24
25
25
26
27
28
28
29
30
31
32
32.5
32.5
32.5
32.5
1Shock upper body
2Spring preload adjuster
3Measurement reading (millimeters)
Figure 7. Measurement Reading
MAINTENANCE
WARNING
Shock absorbers contain compressed nitrogen. Attempting to service shock absorbers can cause an explosion, which could result in death or serious injury. Servicing requires special tools and training from Öhlins. (17604a)
1. Service for the shocks is recommended every 18,600 miles (30,000 km) or 3 years.
2. Maintain product packaging to be used to send the shocks to an Öhlins certified dealer for service, as needed.