80GRIT™ FOOTBOARD KIT - RIDER
J067852024-08-01
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) | Time |
|---|---|---|---|
50501602, 50501604 | Safety Glasses, Torque Wrench |  | 1 hour |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Rider Footboard Components
Table 2. Kit Contents: Rider Footboard Components
 | Item | Qty | Description | Part No. | Notes |
|---|---|---|---|---|---|
 | 1 | 4 | Screw | 10500161 | Torque: 6.8 - 9 Nm (60 - 80 in-lbs) |
| 2 | 4 | Nut | 7716 | |
| 3 | 2 | Footboard bracket, front, rider | 50501793 | |
| 4 | 2 | Footboard, black, rider | 50501626 | Kit 50501604 |
Footboard, raw, rider | 50501625 | Kit 50501602 | |||
| 5 | 2 | Wear plate | 50501661 | |
| 6 | 4 | Screw, wear plate | 10200659 | Torque: 2.03 Nm (18 in-lbs) |
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
FLTRXSTSE models: Separate purchase of Front Support Mounts (Part No. 47200302A - qty of 2) is required. See service manual for removal of old front supports and install of new supports.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
PREPARE
| 1. | Set motorcycle upright. See Secure the Motorcycle for Service in the service manual. |
REMOVE
| 1. | Remove Original Equipment (OE) pivot screw nuts and pivot screws. See the service manual. | |
| 2. | Remove OE footboards. See the service manual. | |
| 3. | NOTE Save screw for install. |
INSTALL
| 1. | Clean and inspect footboard brackets. Replace if worn, rusted or damaged. | |
| 2. | See Figure 1. Install footboard. a. Install new front rider footboard bracket (3) using OE fasteners. b. Install new shoulder bolts (1) and footboard (4). c. Tighten front rider footboard bracket (3) fastener. See the service manual. d. Apply threadlocker and install nut (2). Tighten. Torque: 6.8–9 N·m (60–80 in-lbs) | |
| 3. | Check that foorboard pivots freely on screws (1). | |
| 4. | Repeat for opposite side. |
NOTE
Avoid contacting chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result.
REPLACE WEAR PLATE
| 1. | Remove screws (6). | |
| 2. | Replace wear peg (5). | |
| 3. | Apply threadlocker to threads of screws and install. Tighten. Torque: 2 N·m (18 in-lbs) |