HIGH-TOP SEAT KIT
941003172024-02-22
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
52000655, 52000655A | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: High-Top Seat Kit
Table 2. Kit Contents: High-Top Seat Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | High-Top rider seat | Not sold separately | |
| 2 | 1 | High-Top passenger pillion | Not sold separately | |
| 3 | 2 | Seat screw | 10201398 | |
| 4 | 2 | Fender nut, assembly | 59768-97 | |
| 5 | 4 | Fender tape | 11100176 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
PREPARE
NOTE
When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs.
| 1. | Remove Original Equipment (OE) rider seat and if equipped, passenger pillion. See service manual. |
REMOVE
| 1. | Remove OE spanner wrench and document pouch from underneath rider seat. See service manual. | |
| 2. | RH975: Figure 2 Remove rear fender plug (1). |
INSTALL
Rider Seat
| 1. | Install OE spanner wrench and document pouch to seat. See service manual. | |
| 2. | Install new rider seat. See service manual. | |
| 3. | Pull up on rider seat to verify it is secure. |
Passenger Pillion
| 1. | Figure 3 Install fender nuts and clips (3). a. From underneath the fender, position fender nut to notch in fender hole and install. b. Above the fender, install clip to lock fender nut in place. | |
| 2. | Mark and apply protective tape (2). a. Mark bottom of pillion isolators (1) with chalk. b. Set pillion in place and press down to transfer marks to fender. c. Place protective tape (2) on rear fender over marks. | |
| 3. | Figure 4 Install passenger pillion. a. Engage front mount tab (3). b. Secure with screws (1). Tighten. Torque: 2.3–4.6 N·m (20–41 in-lbs) | |
| 4. | Pull up on passenger pillion to verify that it is secure. |
| 1 | Rear fender plug |
| 2 | Front mount location |
| 3 | Fender nut locations |
Figure 2. Remove Fender Rear Plug
| 1 | Pillion isolator (4) |
| 2 | Protective tape (4) |
| 3 | Fender nut and clip (2) |
Figure 3. Protective Tape
| 1 | Screw (2) |
| 2 | Seat |
| 3 | Front mount tab |
Figure 4. Install Passenger Pillion