0/0
TRANSPARENT PAINT GUARD KIT - SADDLEBAG LID
941004952024-01-23
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
11100311
Safety glasses, Isopropyl alcohol, Squeegee (small), Spray bottle, Microfiber cloth
(1) Only simple tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Transparent Paint Guard
Table 2. Kit Contents: Transparent Paint Guard Kit
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Paint guard, top, right
Not sold separately
2
1
Paint guard, top, left
Not sold separately
3
1
Paint guard, side, right
Not sold separately
4
1
Paint guard, side, left
Not sold separately
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
Separate purchase of two one-quart spray bottles, Johnson &Johnson® Baby shampoo and 70% isopropyl alcohol.
Separate purchase of a 3M squeegee (3M part number 71607 or equivalent) is required for proper installation of this kit.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
PREPARE
NOTE
Prepare solutions on the day of installation.
1. Prepare two solutions in spray bottles:
a. Slip Solution: Thoroughly mix 16 oz. (473 mL) of distilled water and 2-3 drops of baby shampoo. The solution sheets off the paint guards with minimum froth.
b. Tack Solution: Using 70% isopropyl rubbing alcohol, mix a solution that is 10% alcohol and 90% distilled water.
2. Wash all mounting areas thoroughly. Allow to dry completely.
Installation Tips and Tricks
  • Do not apply to new paint (including touch-up paint). Allow paint to cure for a minimum of 30 days before applying the paint guards.
  • Do not apply in windy conditions or in direct sunlight.
  • Make sure that ambient temperature is between 15-32° C (60-90° F).
  • Wash hands throughly and keep fingers wet with water/shampoo mixture during installation. To avoid fingerprints, do not touch adhesive with dry fingers.
  • Keep paint guard film and squeegee wet during installation.
  • See Figure 1. Identify each paint guard piece and its mounting location before proceeding.
  • For top saddlebag lid tape, start with the rear of the piece. For side saddlebag lid tape, start with the front edge of the piece.
  • When smoothing the paint guards into place with the squeegee, work from the center toward the edges. Continually spray the paint guards with solution during the installation.
  • The soap solution allows for slight repositioning of the paint guard.
  • The alcohol solution fixes the adhesive to the lids and can slightly stretch the paint guard film.
  • If wrinkles are found after applying the alcohol solution, spray more alcohol solution under the wrinkle and squeegee again. Continue to smooth out wrinkles along edges as the solution dries if necessary.
INSTALL
NOTE
For top saddlebag lid tape, start with the rear of the piece. For side saddlebag lid tape, start with the front edge of the piece.
1. Wet mounting surface and fingers thoroughly with soap solution.
2. For top adhesive piece, align paint guard with rear edge. For side adhesive piece, align paint guard with leading edge of top tape.
3. Roll a small section of paper backing away from adhesive surface. Spray adhesive surface with soap solution. Align with a straight edge of mounting surface. When aligned properly, slow roll remaining backing from film.
4. When backing is fully removed, spray entire paint guard film with soap solution and smooth film into place by hand.
5. Once positioned properly, gently lift rear edge of film about halfway.
NOTE
If repositioning is needed, spray more of the soap solution on paint guard and hands and position as necessary.
6. Spray film and mounting surface with water/alcohol mixture.
7. Start squeegee from center and work toward rear edge to remove air bubbles.
8. Use firm and overlapping strokes with squeegee to work out all air. Do not cut or tear film.
9. Gently lift other side of film and repeat steps 6-8.
10. Wipe paint guard dry with a Harley-Davidson® Microfiber Detailing Cloth (Part No. 94663-02 or 93600136).
a. Check for water pockets or air bubbles.
b. If necessary, spray with more alcohol solution and squeegee again.
c. If necessary, paint guard film can still be lifted to reposition. Spray paint guard film, mounting surface and your fingers with alcohol solution.
d. Squeegee again until all water pockets and air bubbles are removed.
11. Repeat all steps for other paint guard pieces.
COMPLETE
1. Check edges for adhesion.
a. If any area is not adhered, wrap squeegee with a Harley-Davidson® Microfiber Detailing Cloth (Part No. 94663-02 or 93600136) and squeegee edges again.
2. Allow paint guards to cure for 24 hours.
3. Paint guards can then be washed and waxed with the same recommended products used for the vehicle. See owner's manual for recommended products.