HARLEY-DAVIDSON AUDIO POWERED BY ROCKFORD FOSGATE SECONDARY SUBWOOFER INSTALLATION KIT

941006082024-07-02

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
69203434	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Harley-Davidson Audio Powered By Rockford Fosgate Secondary Subwoofer Installation Kit

Table 2. Kit Contents: Harley-Davidson Audio Powered By Rockford Fosgate Secondary Subwoofer Installation Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	6	Anchor, cable strap	69200342
2	8	Cable strap	10065
3	1	Internal harness with panel mount	Not sold separately
4	1	Template, drill	76001389
5	6	Screw, T15	10200065
6	1	Harness, secondary subwoofer	Not sold separately

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A Service Manual and Electrical Diagnostic Manual (EDM) for the year and model motorcycle is required for this installation.

These items are available at your local Harley-Davidson dealership.

Separate purchase of a Primary Subwoofer Kit (Part No. 76001376) is required for this installation.
Separate purchase of Secondary Amplifier Kit (Part No. 76001444) is required for this installation.
Separate purchase of a Secondary Subwoofer Kit (Part No. 76001377) is required for this installation.

Installation by a technician at a Harley-Davidson dealership is recommended.

To ensure proper audio performance, speaker set up in the Infotainment Control Unit (IFCU) OR Digital Technician II (DT II) is required for audio configuration and amplifier firmware update.

PREPARE

NOTE

Models with security: Disable security system. See service manual.

1.	Remove left and right saddlebags. See service manual.
2.	Remove left and right side covers. See service manual.
3.	Remove main fuse. See service manual.
4.	Remove seat. See service manual.

MODIFY SADDLEBAG

Vehicles Without Saddlebag Lid Speakers Only

NOTE

Drill template must lay flat against all saddlebag surfaces to position holes properly.

1.	Figure 2 Position drill template (1) on back of left saddlebag with orange side facing in toward saddlebag. NOTE Take extreme caution not to damage the painted surface. It is recommended to mark holes with a soft tip marker, then measuring the marks with a scale or calipers to ensure proper hole alignment to the internal harness panel. a. Install drill template (1) over rear mount grommet (2). b. Follow contour (3) of saddlebag under grommet (2). c. Fold drill template (5) over bottom of saddlebag where indicated. d. Use tape (4) to secure drill template (1) in several locations.
2.	Modify left saddlebag. NOTE Use extreme caution not to cut outside of connector hole perimeter to prevent a loose panel fit or improper gasket seal. a. Center punch drill locations marked (A and B) on template. b. Drill six mounting holes at location (A). Diameter: 6 mm (¼ in) c. Drill two connector pass thru holes at location (B). Diameter: 70 mm (2¾ in) d. De-burr edges of hole by lightly sanding the surface.

1	Drill template
2	Grommet
3	Saddlebag contour
4	Tape (4)
5	Template fold

Figure 2. Drill Template (typical)

REMOVE

Vehicles Equipped With Panel Connectors

NOTE

Use caution as harness panel screws have lock patch and can easily be stripped.

1.	Remove left saddlebag audio OE harness panel. See Service Manual.
2.	Remove audio harness from interior of saddlebag.

INSTALL

Install harness panel.

a. Figure 3 Install harness panel (5).

1.2.	Install screws (6). Tighten. Torque: 2.28–2.79 N·m (20.2–24.7 in-lbs)

1	Harness
2	Harness panel cover
3	Secondary subwoofer connector [367B]
4	Speaker connectors [37B] (2)
5	Harness panel
6	Screw (6)

Figure 3. Amplifier Harness Panel

If equipped with saddlebag lid speakers and/or power locks, see EDM. Others skip ahead to step 5.

a. Figure 1 Original 6 way left saddlebag speaker/lock harness connector [288B] is replaced with the 8 way connector from secondary subwoofer harness (6).

b. Remove all wires from original 6 way left saddlebag harness connector [288B].

c. Figure 4 Remove seal plugs from cavities 1 thru 4 (as required below) in new left saddlebag 8 way harness connector [288B].

d. If equipped with speakers, install LBE/O speaker wire into cavity 1 (1).

e. If equipped with speakers, install LBE/GY speaker wire into cavity 2 (2).

f. If equipped with power locks, insert TN/O power lock wire terminal into cavity 3 (3).

g. If equipped with power locks, insert TN/R power unlock wire terminal into cavity 4 (4).

1	Cavity 1 LBE\O Wire speaker positive
2	Cavity 2 LBE\R Wire speaker negative
3	Cavity 3 TN\O Wire power lock
4	Cavity 4 TN\R Wire power unlock
5	Cavity 5 BN\GY Wire secondary subwoofer negative
6	Cavity 6 BN\R Wire secondary subwoofer positive
7	Cavity 7 BK Wire secondary subwoofer detect negative
8	Cavity 8 GY Wire secondary subwoofer detect positive

Figure 4. Connector [288B] View

Figure 1 If equipped with power locks, remove seal plugs from cavity 1 and 2 in left saddlebag, 8 way panel connector [288A] (3).

a. Figure 5 Using audio/lock harness removed from saddlebag earlier, insert TN/O power lock wire terminal into cavity 3 (3).

b. Insert TN/R power unlock wire terminal into cavity 4 (4).

1	Cavity 1 LBE\O Wire speaker positive
2	Cavity 2 LBE\R Wire speaker negative
3	Cavity 3 TN\O Wire power lock
4	Cavity 4 TN\R Wire power unlock
5	Cavity 5 BN\GY Wire secondary subwoofer negative
6	Cavity 6 BN\R Wire secondary subwoofer positive
7	Cavity 7 BK Wire secondary subwoofer detect negative
8	Cavity 8 GY Wire secondary subwoofer detect positive

Figure 5. 8-Way Panel Connector [288A] View

Route power lock wires out the bottom of harness panel along audio harness.

Figure 3 Install harness panel cover (2).

Figure 3 Interior harness will be routed as shown. Anchors/cable straps and wire guides will be used when installing subwoofer kit.

Figure 1 Install secondary subwoofer wire harness (6).

NOTE

If installing a with additional speaker kits, wait until all speaker components are installed prior to making any connections. See the appropriate speaker or harness kit installation instructions.

b. Mount saddlebag to check harness length. Leave enough length to easily connect to saddlebag.

c. Make certain harness will not contact any moving parts.

d. Tighten cable straps securing rear section of harness.

7.1.	Figure 6 Connect and route external wire harness along left rear frame rail. Using cable straps loosely install harness to anchor points (1). Do not tighten cable straps.

1	Anchor point
2	External wire harness connector [288B]

Figure 6. Harness Routing (Left)

Route harness forward between rear fender and frame into battery box area.

a. Figure 7 Connect left saddlebag external harness connector [351B] to right saddlebag amp output harness connector [351A] (4) (both identified with blue tape).

1	[325A_1] Rear PNA (12 way)
2	[350A_1] A2B In (yellow tape)
3	[350B_1] A2B Out (green tape)
4	[351A_1] RH Amp Output (light blue and blue tape)

Figure 7. External Harness Underseat Routing Top View

Figure 8 Route remaining left saddlebag exterior harness branch along right saddlebag amp harness and secure with cable straps.

a. Remove seal plug from cavity 5 and 6 of 6 way right saddlebag connector [289B].

b. Insert BK wire terminal into cavity 5 (1).

d. Reassemble harness connector [289B] into panel connector [289A].

9.3.	Insert GY wire terminal into cavity 6 (2).

1	Cavity 5 install BK wire
2	Cavity 6 install GY wire

Figure 8. 6 Way Right Saddlebag Connector [289B]

10.

Cap any unused connectors with seal plugs provided.

COMPLETE

NOTE

To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.

Complete installation of all audio kits prior to performing these operations.

1.	Install seat. After installing seat, pull up on the seat to verify that it is secure. See service manual.
2.	Install main fuse. See service manual.
3.	Install side covers. See service manual.
4.	Install saddlebags. See service manual.

CONFIGURE

1.	Perform system configuration ONLY after all audio accessory kits have been installed.
2.	Power up vehicle in accessory mode.
3.	On the Infotainment Control Unit (IFCU): a. Select: Settings icon. b. Select: Sounds Settings. c. Follow on screen prompts for applicable audio system changes.
4.	When complete, turn power off for 60 seconds.
5.	Turn power back on, verify proper operation of audio system.