0/0
TOUR-PAK WALL ORGANIZER
J057452013-03-15
GENERAL
Kit Number
53000303
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Kit Contents
See Figure 3 and Table 1.
INSTALLATION
NOTE
Maximum Wall Organizer weight capacity is 1.4 kg (3 lb) evenly distributed.
WARNING
Do not exceed Tour-Pak weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00401c)
Tour-Pak with Molded Liner
  1. Pull the Tour-Pak® liner away from the Tour-Pak wall. With a damp cloth, wipe the Tour-Pak wall clean.
  2. See Figure 3. Use the alcohol wipe (1) and clean the interior surface of the Tour-Pak in the hook-and-loop strips mounting locations. Allow Tour-Pak to dry completely.
    3. NOTE
    The hook-and-loop strips and organizer must be installed below the edge of Tour-Pak base to avoid interference with top gasket and lock.
    The ideal temperature range for applying the fastener strip is 70-100° F (21-38° C). Minimum application temperature is 50° F (10° C). If the temperature is too low, the adhesive will not adhere properly.
  3. Remove the protective tape. Press the hook-and-loop strips into the locations (1) shown in Figure 1. The hook-and-loop strips should be located approximately 3 mm (⅛ in) below the edge of the Tour-Pak base.
    4. NOTE
    The lower hook-and-loop strips ( Figure 3 , item 9) attached to the wall organizers are not used on a Tour-Pak® with a liner.
  4. See Figure 1. Install hinge strips to the Tour-Pak wall organizers.
    1. Remove upper hook-and-loop strips (1 and 2) from the center Tour-Pak wall organizer (5).
    2. Install the hook-and-loop hinges (3 and 4) to the center Tour-Pak wall organizer.
    3. Install the hook-and-loop strips (1 and 2) to the hook-and-loop hinges.
    4. Remove the lower hook-and-loop strip ( Figure 3 , item 9) from the center Tour-Pak wall organizer.
    5. Repeat procedure for left and right Tour-Pak wall organizers.
  5. See Figure 2. Install the Tour-Pak wall organizers (2, 3 and 4) to the Tour-Pak. Start with the center Tour-Pak wall organizer.
    1. Test fit the Tour-Pak wall organizers to verify fit. Install the left and right Tour-Pak wall organizers so that the mesh pockets are at the rear of the Tour-Pak base. The cut out of the center Tour-Pak wall organizer locates around Tour-Pak lid tether anchor.
    2. Fit the hook-and-loop strip side of the hook-and-loop hinge between the liner and Tour-Pak wall.
    3. Verify the fit of the Tour-Pak organizers.
    4. Remove the protective tape from the hook-and-loop strip (8, 10 or 11). Insert the hook-and-loop hinge between the liner and Tour-Pak wall. Adhere the hook-and-loop strip to the Tour-Pak wall. Repeat for the other two organizers.
  6. Verify that the Tour-Pak lid closes over the organizer and the lock works without interference. Adjust as necessary.
  7. Allow adhesive to cure ("wet-out") for a minimum of 48 hours at 70° F (21° C) (allow extra time if temperature is below 70°). Do not place items in the Wall Organizer while adhesive is curing.
1Hook-and-loop strip (loop side), 11 in (30 cm)
2Hook-and-loop strip (loop side), 3.5 in (8.9 cm)
3Hook-and-loop hinge, 11.5 in (29.2 cm)
4Hook-and-loop hinge, 4 in (10.2 cm)
5Center Tour-Pak wall organizer
Figure 1. Install Hinge Strip to Organizer
1Left Tour-Pak organizer
2Center Tour-Pak organizer
3Right Tour-Pak organizer
Figure 2. Mounting locations
Tour-Pak without Molded Liner
NOTE
Hinge strips ( Figure 3 , items 5, 6 and 7)are not used on a Tour-Pak® without a liner.
  1. Clean the interior wall of the Tour-Pak with a damp cloth.
  2. See Figure 3. Use the alcohol wipe (1) and clean Tour-Pak hook-and-loop strips mounting locations. Allow Tour-Pak to dry completely.
    3. NOTE
    The hook-and-loop strips and organizer must be installed below the edge of Tour-Pak base to avoid interference with top gasket and lock.
    The ideal temperature range for applying the fastener strip is 70-100° F (21-38° C). Minimum application temperature is 50° F (10° C). If the temperature is too low, the adhesive will not adhere properly.
  3. See Figure 2. Install the Tour-Pak wall organizers (2, 3 and 4) to the Tour-Pak. Start with the center Tour-Pak wall organizer.
    1. Test fit the Tour-Pak wall organizers to verify fit. Install the left and right Tour-Pak wall organizers so that the mesh pockets are at the rear of the Tour-Pak base. The cutout of the center Tour-Pak wall organizer locates around Tour-Pak lid tether anchor.
    2. Remove the protective tape from the hook-and-loop strip ( Figure 3 , items 8-11).
    3. Adhere the hook-and-loop strip to the Tour-Pak wall.
    4. Repeat for the other two organizers.
  4. Verify that the Tour-Pak lid closes over the organizer and the lock works without interference. Adjust as necessary.
  5. Allow adhesive to cure ("wet-out") for a minimum of 48 hours at 70° F (21° C) (allow extra time if temperature is below 70°). Do not place items in the Wall Organizer while adhesive is curing.
KIT CONTENTS
Figure 3. Kit Contents: Tour-Pak Wall Organizer
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
Alcohol wipe
Not Sold Separately
2
Tour-Pak wall organizer, center
Not Sold Separately
3
Tour-Pak wall organizer, right
Not Sold Separately
4
Tour-Pak wall organizer, left
Not Sold Separately
5
Hook-and-loop hinge, 40.6 cm (16 in)
Not Sold Separately
6
Hook-and-loop hinge, 29.2 cm (11.5 in)
Not Sold Separately
7
Hook-and-loop hinge, 10.2 cm (4 in)
Not Sold Separately
8
Hook-and-loop strip (loop side) 34.3 cm (13.5 in)
Not Sold Separately
9
Hook-and-loop strip (loop side) 38.1 cm (15 in)
Not Sold Separately
10
Hook-and-loop strip (loop side) 30 cm (11 in)
Not Sold Separately
11
Hook-and-loop strip (loop side) 8.9 cm (3.5 in)
Not Sold Separately
12
Hook-and-loop strip (loop side) 6.4 cm (2.5 in)
Not Sold Separately