TWO-UP ONE-PIECE SOFTAIL SEAT KITS

J064362024-03-08

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
52000295, 52000297, 52000298, 52000300, 52000305, 52000349, 52000350, 52000353, 52000354, 52000355, 52000356, 52000387, 52000388, 52000400, 52000401, 52000652, 52000653, 52000759, 52000761	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Two-Up One-Piece Softail Seat

Table 2. Kit Contents: Two-Up One-Piece Softail Seat Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Seat thumb screw	3075	Kits 52000295, 52000300, 52000355, 52000387, 52000388, 52000401
1	1	Seat thumb screw	10201398	Kits 52000652, 52000653, 52000759, 52000761
2	1	Mounting bracket, rear	51652-97A	Kits 52000295, 52000297, 52000300, 52000355, 52000356
			52400209	Kit 52000387, 52000400
			52400285	Kit 52000298, 52000305, 52000350, 52000354
			52400359	Kit 52000349, 52000353
3	2	Flange screw	3588	Kits 52000295, 52000297, 52000300, 52000355, 52000356, 52000388, 52000401
	2		965M	Kit 52000349, 52000353
	2		67956-96	Kits 52000298, 52000305, 52000350, 52000354
	1		3901	Kits 52000652, 52000653, 52000759, 52000761
4	1	Grab strap	52400151	Kits 52000295, 52000305, 52000354
			52400192	Kits 52000355, 52000356
			52400193	Kit 52000349
			52400194	Kit 52000350
			52400098	Kit 52000297
			53031-05	Kit 52000300
			52400214	Kits 52000387, 52000388, 52000400, 52000401
			53031-05	Kit 52000298
			52400146	Kit 52000353
			52400325	Kits 52000652, 52000653, 52000759, 52000761
5	11	Seat isolator	11100174	Kits 52000295, 5200297, 52000298, 52000300, 52000305, 52000350, 52000354,52000355, 52000356, 52000387, 52000388, 52000400, 52000401
5	12	Seat isolator	11100174	Kits 52000349, 52000353
6	1	Screw, grab strap	3901	Kits 52000295, 52000297, 52000300, 52000355, 52000356, 52000652, 52000653
6	1	Screw, grab strap	10200036	Kits 52000387, 52000388, 52000400, 52000401
7	1	Washer, grab strap	6036	Kits 52000295, 52000297, 52000300, 52000355, 52000356, 52000387, 52000388, 52000400, 52000401, 52000652, 52000563, 52000759, 52000761
8	2	Retention washer (part of seal nut kit 59768-97)	Not sold separately	Kits 52000295, 52000300, 52000355, 52000387, 52000388, 52000400, 52000401
8	1	Retention washer (part of seal nut kit 59768-97)	Not sold separately	Kits 52000297, 52000356
9	4	Protective tape	11100176	Kits 52000295, 52000297, 52000300, 52000355, 52000387, 52000400, 52000653, 52000761
9	6	Protective tape	11100176	Kit 52000652, 52000759
10	2	Retention nut (part of seal nut kit 59768-97)	Not sold separately	Kits 52000295, 52000300, 52000355, 52000387, 52000388, 52000400, 52000401
	1	Retention nut (part of seal nut kit 59768-97)	Not sold separately	Kits 52000297, 52000356, 52000652, 52000653, 52000759, 52000761
	2	Flange nut, large	7499	Kits 52000652, 52000653, 52000759
11	1	Cable strap (not shown)	10039	Kits 52000759, 52000761
11	1	Cable strap (not shown)	10140	Kits 52000652, 52000653

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Do not install these seat kits on motorcycles that are not equipped with an appropriate grab strap and passenger footpegs. If footpegs and grab strap are not installed, passenger could fall from moving motorcycle or grab onto operator, causing loss of control and death or serious injury. (00410b)

Separate purchase of passenger footpegs is required if installed on a vehicle originally equipped with a solo seat.

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

REMOVE

NOTE

When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs.

1.	Remove seat. See service manual. a. Retain seat mounting screw.
2.	Kit 52000297 only: Remove protective tape from rear fender. NOTE Kit 52000353: Reuse Original Equipment (OE) grab strap from vehicle.
3.	All kits except 52000353: Figure 1 Remove and discard OE grab strap. a. Kits 52000298, 52000305, 52000349, 52000350, 52000354, 52000652, 52000653, 52000759, 52000761: Discard large OE seat nuts.
4.	Figure 2 Remove studded seat bracket, if equipped. Discard. a. Remove nylon retaining washers (1) from bracket studs (2). b. Remove studded bracket from fender.

INSTALL

1.	Kits 52000295, 52000297, 52000300, 52000355, 52000356, 52000387, 52000388, 52000400, 52000401, 52000652, 52000653: Figure 3 Install retention nut and retention washer in appropriate fender holes. a. A cable strap may be used as an installation aid to install retention nut and washer. Place retention nut (1) over cable strap (3). b. Thread cable strap up under fender and through appropriate fender hole. Pull up on cable strap to hold nut snug against underside of fender. c. With rib on retention nut seated into notch in the appropriate fender hole, slide retention washer (2) into place from rear. This will lock retention nut in place. d. Remove cable strap.
2.	Kits 52000295, 52000297, 52000300, 52000355, 52000387, 52000400: Figure 1 Install protective tape. a. Mark bottom of isolators (5) that contact fender with chalk. b. Set seat in place with front and rear mounting locations on the seat aligned with mounting locations on the vehicle. c. Press down on seat to transfer the marks from isolators to the fender. d. Kit 52000652, 52000653, 52000759, 52000761: Figure 1 If vehicle is equipped with stud plate, use stud plate to attach grab strap using flange nuts (10) from kit. e. Install protective tape (9) on rear fender over marks transferred to fender.
3.	All kits except 52000353: Figure 1 Install grab strap (4), screw (6) and washer (7). Tighten. Torque: 6.75–10.2 N·m (60–90 in-lbs) NOTE Do not allow seat to contact painted surfaces when sliding it through grab strap or damage to paint can occur.
4.	Figure 1 Slide back of seat through grab strap and hook front tab of seat (12) into frame (11).
5.	Install seat bracket to fender with OE seat mounting screw. Tighten. Torque: 1.7–3.4 N·m (15–30 in-lbs)
6.	After installing seat, pull up on seat to verify that it is secure. See service manual.

1	Nylon retaining washer (2)
2	Bracket stud (2)
3	Flange nut (2)

Figure 2. Studded Seat Bracket

Figure 3. Installation Tool