ADVERSARY MIRRORS
941000762022-08-04
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
56000224, 56000225 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Mirror
Table 2. Kit Contents: Mirror Kits
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Mirror, right - Black | 56000226 | |
| Mirror, right - Gray | 56000227 | |||
| 2 | 1 | Mirror, left - Black | 56000228 | |
| Mirror, left - Gray | 56000229 | |||
| 3 | 1 | Tube nut, right | 10100149 | 12–14 N·m (9–10 ft-lbs) |
| 4 | 1 | Tube nut, left | 10100150 | |
| 5 | 1 | Clamp, right | 41700623 | Right mirror has left hand threads |
| 6 | 1 | Clamp, left | 36700236 | Left mirror has right hand threads |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
- Separate purchase of Handlebar End Cap (Part No. 55801095, 55900246, 55900247 or 55900248) is required for installation.
These items are available at your local Harley-Davidson dealership.
REMOVE
For All Models Except RA1250S:
| 1. | Figure 2 Remove Original Equipment (OE) bar end mirror. a. Remove and discard screw (1). b. Remove and discard mirror base (2). | |||||
| 2. | Install handlebar end caps. Installation Requirements | |||||
| 3. | Figure 3 Remove OE screws (4) and clamp half (3) from clutch and front master cylinder. Save screws (4) for later use. | 
Figure 2. Bar End Mirror |
For Model RA1250S:
| 1. | Figure 3 Loosen mirror nut (2) and remove mirror. | |
| 2. | Leave end caps and mirror half clamps on vehicle. |
INSTALL
NOTE
- Clutch lever clamp half has number 36700236 imprinted on component.
- Left mirror has right hand threads. Right mirror has left hand threads.
For All Models Except RA1250S:
| 1. | Figure 3 Install new clamp half (3). | |
| 2. | Position hand control as needed. | |
| 3. | Install screws (4). Do not tighten completely. a. Fully seat and tighten top screw (4). Torque: 7–9 N·m (62–80 in-lbs) b. Fully seat and tighten bottom screw (4). Torque: 7–9 N·m (62–80 in-lbs) | |
| 4. | Install mirror. a. Install mirror nut (2) onto mirror stem until loosely seated. b. Loosely install mirror (1) into clamp half (3). c. Adjust mirror stem (1) position. d. Tighten mirror nut (2) against clamp half (3). Careful not to damage nut finished surface. Torque: 12–14 N·m (106–124 in-lbs) | |
| 5. | Repeat procedure for opposite side. |
| 1 | Mirror |
| 2 | Tube nut |
| 3 | Clamp half |
| 4 | Screw (2) |
Figure 3. Mirror Assembly (Typical)
For model RA1250S:
| 1. | Figure 3 Install mirror. a. Install mirror nut (2) onto mirror stem until loosely seated. b. Loosely install mirror (1) into clamp half (3). c. Adjust mirror stem (1) position. d. Tighten mirror nut (2) against clamp half (3). Careful not to damage nut finished surface. Torque: 12–14 N·m (106–124 in-lbs) |