MIRROR KIT

941001922022-08-08

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
56000220, 56000221, 56000241, 56000261	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Mirror Kit

Table 2. Kit Contents: Mirror Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Left mirror	56000240
		Left mirror, round	56000271
		Left mirror, Empire, Black	56000215
		Left mirror, Empire, Edge cut	56000217
2	1	Right mirror	56000236
		Right mirror, round	56000273
		Right mirror, Empire, Black	56000216
		Right mirror, Empire, Edge cut	56000218
3	1	Right mirror nut	10100136	Kit 56000241 Only
3	1	Right mirror nut, black	10100149
4	1	Right clamp half	41700623
5	1	Left clamp half	36700236
6	1	Left mirror nut	10100135	Kit 56000241 Only
6	1	Left mirror nut, black	10100150

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

These items are available at your local Harley-Davidson dealership.

Separate purchase of Handlebar End Cap (Part No. 55801095, 55900246, 55900247 or 55900248) is required for installation.

REMOVE

For all models except RA1250S:

1.	Figure 2 Remove Original Equipment (OE) bar end mirror. a. Remove and discard screw (1). b. Remove and discard mirror base (2).
2.	Install handlebar end caps. Installation Requirements
3.	Figure 3 Remove screws (4) from OE clamp half on clutch and front master cylinder. Save for later use.
4.	Remove and discard OE clamp half (3).

1	Screw
2	Mirror base

Figure 2. Bar End Mirror

For model RA1250S:

1.	Figure 3 Loosen mirror nut (2) and remove mirror.
2.	Leave end caps and mirror half clamps on vehicle.

INSTALL

NOTE

Clutch lever clamp half will have number 36700236 imprinted on component.

Left mirror has right hand threads. Right mirror has left hand threads.

For all models except RA1250S:

1.	Figure 3 Install new clamp half (3).
2.	Position hand control as needed.
3.	Install screws (4). Do not tighten completely. a. Fully seat and tighten top screw (4). Torque: 7–9 N·m (62–80 in-lbs) b. Fully seat and tighten bottom screw (4). Torque: 7–9 N·m (62–80 in-lbs)
4.	Install mirror. a. Install mirror nut (2) onto mirror stem until loosely seated. b. Loosely install mirror (1) into clamp half (3). c. Adjust mirror stem (1) position. d. Tighten mirror nut (2) against clamp half (3). Careful not to damage nut finished surface. Torque: 12–14 N·m (106–124 in-lbs)
5.	Repeat procedure for opposite side.

1	Mirror
2	Mirror nut
3	Clamp half
4	Screw

Figure 3. Mirror Assembly

For model RA1250S:

Figure 3 Install mirror.

a. Install mirror nut (2) onto mirror stem until loosely seated.

b. Loosely install mirror (1) into clamp half (3).

c. Adjust mirror stem (1) position.

d. Tighten mirror nut (2) against clamp half (3). Careful not to damage nut finished surface.

Torque: 12–14 N·m (106–124 in-lbs)