Kits | Suggested Tools | Skill Level(1) |
---|---|---|
93300129 | Safety Glasses |
Verify that all contents are present in the kit before installing or removing items from vehicle. | |||||
---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
1 | 1 | Bag, tank | Not sold separately | ||
2 | 2 | Screw | 10201138 | ||
3 | 2 | Washer | 10300236 | ||
4 | 2 | O-ring | 11159 | ||
5 | 2 | Spacer | 12400206 | ||
6 | 1 | Strap, front | 93300154 | ||
7 | 1 | Strap set, tank, rear | 93300146 | ||
8 | 1 | Rain cover | 93300152 | ||
9 | 2 | Protective tape | 11100303 |
1. | Remove seat. See service manual. |
1. | Figure 2 Remove Original Equipment (OE) screws (1) from tank console (2). Discard. |
1 | OE Screw (2) |
2 | Tank console |
1. | Figure 3 Install front mounting straps to tank console. a. Figure 3 Install spacer (1), mounting strap (2), O-ring (3), washer (4) and screw (5). NOTE Install spacer (1) with grooved side facing toward tank. b. Secure screw (5). Tighten. Torque: 3.9–4.8 N·m (35–42 in-lbs) | |
2. | Figure 4 Install rear strap (1) under tank (2). a. Thread rear strap between rear tank mount and tank. b. Pull buckle through loop at other end of strap. c. Eliminate slack in strap system. | |
3. | Figure 5 Position tank bag on tank. | |
4. | Figure 7 Secure front mounting straps to tank bag by connecting quick release buckles. | |
5. | Figure 7 Secure rear mounting strap to tank bag by connecting quick release buckle. | |
6. | Pull straps snug to eliminate slack in strap system. | |
7. | Install protective tape to fuel tank. a. Figure 6 Check for widest point (1) of tank bag. b. Test fit protective tape (1) where tank bag touches the fuel tank. Note location. c. Remove tank bag (3). d. Clean area with 50/50 alcohol and water mixture. e. Wipe dry with clean cloth. f. Peel backing from protective tapes (1) and install in noted location.. g. Install tank bag (3). |
1 | Spacer (2) |
2 | Strap (2) |
3 | O-ring (2) |
4 | Washer (2) |
5 | Screw (2) |
1 | Protective tape (2) |
2 | Widest point |
3 | Tank bag |
1 | Quick release (disconnected) |
2 | Quick release (connected) |
3 | Strap bungee |
1. | Install seat. After installing seat, pull up on seat to verify that it is secure. See service manual. | |
2. | Pull straps tight to secure bag. | |
3. | Check that bag is securely fastened to vehicle. | |
4. | Figure 7 Secure any excess strap length using strap bungee (3). | |
5. | Figure 8 Clip front two straps (1,2), attached to tank console, together when tank bag is removed from vehicle. a. Figure 7 Secure excess strap length using strap bungee (3). |
1. | Pull rain cover over entire bag. | |
2. | Pull draw string at bottom of cover to tighten. | |
3. | Secure with barrel lock | |
4. | Make sure the rain cover is tucked completely under tank bag. |
1. | Use a lint-free cloth to wipe off any dust or dirt. | |
2. | Thoroughly clean outer surface with warm water and a mild detergent. | |
3. | Allow material to dry naturally and completely before use or storage. | |
4. | Do not use washing machine or dryer. | |
5. | Do not use artificial means to dry material quickly. | |
6. | Contains one or more of the following materials: Polyester, Polypropylene, POM, EPDM Rubber, Vinyl. |