DETACHABLE SADDLEBAGS AND RELOCATION KIT
941002602022-06-16
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
90202254, 67801297
Safety Glasses, Torque Wrench
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Detachable Saddlebag
Figure 2. Kit Contents: Turn Signal / License Plate Relocation Kit
Table 2. Kit Contents: Detachable Saddlebag / Turn Signal / License Plate Relocation Kit
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Saddlebag, left
90202324
60% HDPE Plastic, 27% Steel, 13% Vinyl
2
1
Saddlebag, right
90202323
60% HDPE Plastic, 27% Steel, 13% Vinyl
3
1
Lock set kit, handle
90202335
4
2
Nut, locking
10100119
5
2
Screw
10201315
6
2
Spacer, saddlebag
12400218
7
2
Docking hardware, passenger backrest
52300705
8
6
Docking point, saddlebag
90201763
9
4
Screw
10201264
10
2
Nut
10100042
11
2
Screw
4789M
12
1
Turn signal relocation bracket
67801316
13
1
Support bracket, rear fender
59501037
14
1
Lamp, tail light
73504-11
1
Reflector, tail light
67900231
15
2
Screw
10200934
16
6
Connector, insulated, red
70585-93
17
1
Extention, wire harness, turn signal
69200150
18
2
Screw
10200800
19
2
Nut, flange locking
10100145
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
ELECTRICAL CRIMP TOOL (Part Number:HD-48119) is required for installation of this kit.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
WARNING
Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a)
WARNING
See ACCESSORIES AND CARGO section within the SAFETY FIRST section in your owner's manual. Improper cargo loading or accessory installation can cause component failure and adversely affect stability, handling and performance, which could result in death or serious injury. (00021c)
NOTE
  • Do not exceed 12 lbs (5.4 kg) total weight contents and attachments per bag.
  • Periodically recheck load.
WARNING
Do not exceed the motorcycle's Gross Vehicle Weight Rating (GVWR) or Gross Axle Weight Rating (GAWR). Exceeding these weight ratings can lead to component failure and adversely affect stability, handling and performance, which could result in death or serious injury. (00016f)
PREPARE
1. Support vehicle under frame with stand or suitable blocking to prepare for addition of saddlebags.
DOMESTIC VEHICLE
Remove
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
1. Remove main fuse. See service manual.
2. Remove seat. See service manual.
3. Remove rear fender. See service manual.
4. Remove turn signals. See service manual.
a. Cut connectors.
b. Retain screws for later use.
5. Remove tail lamp. See service manual.
a. Cut connectors.
Install
1. Cut and splice new wire length to Original Equipment (OE) turn signal and tail lamp connectors.
a. Insert end of turn signal wire into one side of sealed splice connector.
b. Insert new wire into the other end of sealed splice connector.
c. Crimp ends of sealed splice connector.

Special Tool: ELECTRICAL CRIMP TOOL (HD-48119)

2. See Figure 3. Install OE turn signal lamps (3) to turn signal relocation bracket (1) with screws (2). Tighten.
Torque: 7–9 N·m (62–80 in-lbs)
3. Route wires through tube structure into rear frame fender struts up to connection under seat.
4. See Figure 4. Install rear spacers (1) and docking point (8) to rear fender strut.
5. Secure with screw (7). Tighten.
Torque: 20–26 N·m (15–19 ft-lbs)
6. Install turn signal relocation bracket to fender strut.
a. See Figure 4. Install turn signal relocation bracket (6) to vehicle with screw (3). Hand tighten.
b. Tighten screws (3).
Torque: 9–11 N·m (80–97 in-lbs)
c. See Figure 5. Install Fender support (1), nut plate, passenger docking hardware (2), docking point (8) and screw (7). Tighten.
Torque: 20–26 N·m (15–19 ft-lbs)
d. See Figure 4. Install docking point (8), screw (5) and nut (4).
1Turn signal relocation bracket
2Screw (2)
3OE Turn signal lamps (2)
Figure 3. Turn Signal Install
1Spacer, rear (2)
2Docking hardware, passenger (2)
3Screw (2)
4Nut (2)
5Screw (2)
6Turn signal relocation bracket
7Screw (4)
8Docking point, saddlebag (6)
Figure 4. Relocation Bracket to Vehicle Install
1Fender support bracket
2Docking hardware, passenger (2)
6Turn signal relocation bracket
7Screw (4)
8Docking point, saddlebag (6)
Figure 5. Fender Support Bracket
NON-DOMESTIC VEHICLE
Remove
1. Remove main fuse. See service manual.
2. Remove seat. See service manual.
3. Remove rear fender. See service manual.
4. Remove turn signals. See service manual.
a. Cut connectors.
b. Retain screws for later use.
5. Remove OE license plate bracket from license plate module assembly
Install
1. Remove license plate tail lamp from bracket.
2. Cut and splice new wire length to OE turn signal and tail lamp connectors.
a. Insert end of turn signal wire into one side of sealed splice connector.
b. Insert new wire into the other end of sealed splice connector.
c. Crimp ends of sealed splice connector.

Special Tool: ELECTRICAL CRIMP TOOL (HD-48119)

3. See Figure 3. Install OE turn signal lamps (3) to turn signal relocation bracket (1) with screws (2). Tighten.
Torque: 7–9 N·m (62–80 in-lbs)
4. Route wires through tube frame structure of bracket.
5. Install turn signal relocation bracket to fender struts.
a. See Figure 5. Install rear spacers (2).
b. See Figure 3. Install screw (18) and nut (19). Tighten.
c. Route wires in fender struts to under seat connection.
6. Install rear fender. See service manual.
7. See Figure 6. Install fender support bracket (1).
8. Install license plate module.
9. Install fender support nut plates.
1Fender support bracket
2Rear license plate bracket assembly
Figure 6. Fender Support Bracket Install (Non-Domestic)
Figure 7. OE Tail Lamp Install (Non-Domestic)
SADDLEBAGS
Install
1. See Figure 8. Saddlebag latch knob (2) to be in the unlatched position.
a. Pull latch knob (2) out and rotate to unlatched position.
b. See Figure 8. Latch indicator is red when in the unlatched position.
2. Position saddlebag behind docking points and slid forward.
3. Ensure all docking points are engaged. When saddlebag is fully inserted, latch will engage.
a. See Figure 8. Latch indicator is green when in saddlebag is securely latched to vehicle.
b. See Figure 8. If latch indicator (1) did not automatically latch, rotate latch knob (2) to latched position.
Remove
1. Open lid.
2. See Figure 8. Pull latch knob (2) and rotate to the unlatched position while sliding saddlebag rearward.
1Latch indicator
2Latch Knob
Figure 8. Latch Knob / Indicator
1Saddlebag, left
2Saddlebag, right
Figure 9. Saddlebags Install
COMPLETE
1. Install seat. After seat is installed, pull up on seat to verify that it is secure. See service manual.
2. Install main fuse. See service manual.
3. Remove vehicle under frame stand or blocking.
MAINTENANCE
Docking Point Screws
NOTICE
Failure to tighten hardware to the specified torque could result in damage to the installed accessory. (00508b)
1. After 500 miles of on the road use with saddlebags installed, it is necessary to check the torque on docking point mounting screws. Check that the proper torque is maintained and tighten screws if necessary.
a. Docking point screws.
Torque: 20–26 N·m (15–19 ft-lbs)
2. See Figure 4. There are clearances between docking points (8) and fastener diameters (5,7 ) to account for manufacturing tolerances. If saddlebag does not automatically latch when installed, adjust positions of docking points (8) forward or rearward. Position docking points so that middle docking point fully seats on saddlebag before front and rear docking points bottom out on bag bracket.
a. Loosen docking point screws and adjust position of docking points.
b. Tighten docking point screws.
Torque: 20–26 N·m (15–19 ft-lbs)
Care Instructions
Wash with soap and water.