HAND GRIPS

941003812024-05-03

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
56100605, 56100606, 56100607, 56100616, 56100617, 56100564, 56100565, 56100705, 56100706	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Hand Grips (Typical)

Table 2. Kit Contents: Hand Grips (Typical)

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Empire, left, black	56100643	Kit No. 56100605
2	1	Empire, right, black	56100640	Kit No. 56100605
1	1	Empire, left, edge cut	56100644	Kit No. 56100606
2	1	Empire, right, edge cut	56100641	Kit No. 56100606
1	4	Empire, left, chrome	56100645	Kit No. 56100607
2	4	Empire, right, chrome	56100642	Kit No. 56100607
1	1	Adversary, left, black/orange	56100682	Kit No. 56100616
2	1	Adversary, right, black/orange	56100680	Kit No. 56100616
1	1	Adversary, left, gray	56100683	Kit No. 56100617
2	1	Adversary, right, gray	56100681	Kit No. 56100617
1	1	Grip, left, black	56100600	Kit No. 56100564 End Cap (Part No. 56100598)
2	1	Grip, right, black	56100566	Kit No. 56100564 End Cap (Part No. 56100598)
1	1	Grip, left, silver	56100601	Kit No. 56100565 End Cap (Part No. 56100599)
2	1	Grip, right, silver	56100567	Kit No. 56100565 End Cap (Part No. 56100599)
1	1	Kahuna, left, black	56100709	Kit No. 56100705
2	1	Kahuna, right, black	56100707	Kit No. 56100705
1	1	Kahuna, left, chrome	56100710	Kit No. 56100706
2	1	Kahuna, right, chrome	56100708	Kit No. 56100706

GENERAL

Instruction sheet is also available electronically. To verify you are using the most current version available, do one of the following:

Go to Refer to: h-d.com/isheets
Scan QR code in upper left corner of the instruction sheet

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

PREPARE

1.	Remove left saddlebag. See service manual.
2.	Remove left side cover. See service manual.
3.	Remove main fuse. See service manual.

REMOVE

Left Hand Grip

1.	Figure 2 Remove clutch lever assembly. a. Remove rubber boot (5) from connector. b. Disconnect clutch switch connector (4). c. Remove screws (1). d. Remove washers (2). e. Remove clutch lever assembly (3).
2.	Figure 3 Remove left control module cover. a. Alignment screw (4) (do not remove). b. Remove screws (3). c. Remove cover (2).
3.	Figure 4 Remove hand grip. a. Remove left control module (5) from handlebar. b. Remove hand grip (4).

1	Screw (2)
2	Washer (2)
3	Clutch lever assembly
4	Clutch switch connector
5	Rubber boot
6	Gap
7	Alignment mark

Figure 2. Clutch Lever Bracket

1	Clutch switch wire
2	Cover
3	Screw (2)
4	Alignment screw (do not remove)
5	Cover opening

Figure 3. Left Control Module Cover

1	Clutch switch wire
2	Cable guide
3	Groove
4	Hand grip
5	Left control module

Figure 4. Left Hand Grip

Right Hand Grip

NOTE

Do not allow master cylinder to be positioned upside down.

1.	Figure 5 Remove brake lever assembly. a. Remove rubber boot (3) from connector. b. Disconnect brake switch connector (4). c. Remove screws (2). d. Remove washers (1). e. Remove brake lever bracket (5).
2.	Figure 6 Remove right control module cover. a. Remove screws (1). b. Remove cover (2).
3.	Figure 7 Remove hand grip. a. Open wire bridge (4). b. Disconnect connectors. c. Remove hand grip while sliding whole control module assembly.

1	Washer (2)
2	Screw (2)
3	Rubber boot
4	Brake switch connector
5	Brake lever assembly
6	Gap
7	Alignment mark

Figure 5. Brake Lever Assembly

1	Screw (2)
2	Cover
3	Cover opening
4	Alignment marks

Figure 6. Right Control Module Cover

1	Hand grip
2	Groove
3	Hand grip slot
4	Wire bridge
5	Cover support (2)

Figure 7. Right Control Module Grip

INSTALL

NOTE

Do not allow master cylinder to be positioned upside down.
When routing and closing Right and Left Hand Control Modules (R&LHCMs), verify there are no pinched wires. See service manual.

NOTE

Do not remove alignment screw.

Align alignment screw (4) with alignment hole in handlebar.
Verify alignment screw is properly engaged into hole in handle bar.

NOTE

Failure to do this may result in damage to cover.

Control Housing Alignment

Some models have alignment features in the handlebars and control modules. Do not remove alignment features. Left side has a screw (4), Figure 3 and right side has a post (4), Figure 7.

Align these features with the hole in the handlebar.
Verify alignment feature is properly engaged with the hole in the handlebar.

Other models and accessory handlebars have alignment dots, Figure 8. If accessory handlebars, adjust position of switch housing and brake lever assembly on handlebar for rider comfort.

Handlebars without weld: Figure 8 Install clamp against dots on handlebar, keeping clamp slot between the two dots (2) or line (1).
Handlebars with weld: Figure 8 Install clamp against weld, keeping clamp slot between the two dots (2) or line (1).

Failure to align properly may result in damage to the rear cover or wire pinching.

1	Line
2	Dots
3	Switch Housing

Figure 8. Handlebar Markings

Left Hand Grip

1.	Figure 4 Assemble hand grip and Left Hand Control Module (LHCM). a. Install hand grip groove (3) into LHCM (5). b. Install hand grip (4). c. Install left control module (5) to handlebar. d. Route clutch switch wires (1) through wire guide slot (2).
2.	Figure 3 Install left control module cover. a. Guide clutch switch cable (1) through cover opening (5). b. Install cover (2). Verify alignment screw (4) is properly engaged into hole in handle bar. c. Install screws (3). Tighten. Torque: 4–5 N·m (35–44 in-lbs) DO NOT over tighten.
3.	Figure 2 Install clutch lever assembly. NOTE Carefully install clutch lever to not damage the clutch switch. See service manual. a. Install clutch lever assembly (3). b. Install washers (2) and screws (1). c. Tighten top screw. Torque: 10–11 N·m (89–97 in-lbs) Top screw d. Tighten lower screw. Torque: 10–11 N·m (89–97 in-lbs) Lower screw e. Connect clutch switch connector (4). f. Install rubber boot (5) over connector.

Right Hand Grip

1.	Figure 7 Install hand grip. a. Install hand grip (1) in groove (2) of control module assembly. b. Slide control module assembly with hand grip to handlebar. c. Make sure hand grip slot (3) is positioned correctly. d. Connect connectors. e. Close wire bridge (4) and align pin with handlebar slot. f. Route wires through cover support (5).
2.	Figure 6 Install right control module cover. a. Install cover (2). b. Install screws (1). Torque: 4–5 N·m (35–44 in-lbs)
3.	Figure 5 Install brake lever assembly. a. Install brake lever assembly (5). NOTE When installing Right Hand Control Module (RHCM), verify throttle end play is set correctly. See service manual. b. Install washers (1) and screws (2). c. Tighten top screw. Torque: 10–11 N·m (89–97 in-lbs) Top screw d. Tighten lower screw. Torque: 10–11 N·m (89–97 in-lbs) Lower screw e. Connect brake switch connector (4). f. Install rubber boot (3) over connector.

COMPLETE

1.	Install main fuse. See service manual.
2.	Install left side cover. See service manual.
3.	Install left saddlebag. See service manual.