HOMELINK® GARAGE DOOR CONTROL MODULE KIT

941003892024-06-19

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
41001167	Safety Glasses, Torque Wrench

(1) Special tools or techniques required for installation

KIT CONTENTS

Figure 1. Kit Contents: Homelink Garage Door Control Module Kit

Table 2. Kit Contents: Homelink Garage Door Control Module Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Garage door control module	92600018
2	2	Screw	10201339

GENERAL

Instruction sheet is also available electronically. To verify you are using the most current version available, do one of the following:

Go to h-d.com/isheets
Scan QR code in upper left corner of the instruction sheet

NOTE

This instruction sheet may have a Supplemental Video to assist installer in clarifying a certain part of the assembly. A linked video would be located at the end of this instruction sheet.

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

These items are available at your local Harley-Davidson dealership.

2024 and later FLH models: Separate purchase of HomeLink® Mounting Bracket (Part No. 69203073) is required for installation.
2024 and later FLT models: Separate purchase of HomeLink® Mounting Bracket (Part No. 69203074) is required for installation.
HomeLink® module activation requires Digital Technician II (DT II). Contact a Harley-Davidson dealership.
Some generic remotes may program directly to the garage door opener, but cannot be used to train the HomeLink. Use of original or genuine garage door remote may be necessary for successful programming of the HomeLink.

FCC (USA) and IC (Canada)

This device complies with FCC rules part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received including interference that may cause undesired operation. WARNING: The transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End Users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must be at least 5cm from the user and must not be co-located or operating in conjunction with any other antenna or transmitter.

The term "IC:" before the certification/registration number only signifies that Industry Canada technical specifications were met.

PREPARE

1.	Remove left saddlebag. See service manual.
2.	Remove left side cover. See service manual.
3.	Remove main fuse. See service manual.
4.	Remove outer fairing. See service manual.
5.	Frame-mounted fairing: Remove headlamp. See service manual.

INSTALL

NOTE

See Installation Requirements for mounting brackets.

Fork-Mounted Fairing Model

1.	Figure 2 Install mounting bracket. a. Slide mounting bracket (3) on screw post. b. Hold tab (6) against media compartment. c. Install screw (2). Tighten. Torque: 5.5–6.8 N·m (49–60 in-lbs)
2.	Install module. a. Install module (1) into mounting bracket (3) until three tabs are engaged. b. Connect and lock connector (5).

1	Module
2	Screw
3	Mounting bracket
4	Tab
5	Connector
6	Tab

Figure 2. Fork-Mounted Fairing Model

Frame-Mounted Fairing Model

1.	Figure 3 Install mounting bracket. a. Install mounting bracket (3) under fairing support bracket. b. Install screws (2). Tighten. Torque: 5.5–6.8 N·m (49–60 in-lbs)
2.	Install module. a. Install rear of module (1) in mounting bracket (3). b. Install front of module into mounting bracket until tab (4) is engaged. c. Connect and lock connector (5).

1	Module
2	Screw (2)
3	Mounting bracket
4	Tab
5	Connector
6	Tab

Figure 3. Frame-Mounted Fairing Model

INFOTAINMENT CONTROL UNIT (IFCU) SETUP

1.	Select: HomeLink icon (1). Figure 4
2.	Follow on-screen prompts for setup.

1	HomeLink Icon

Figure 4. IFCU Screen

COMPLETE

1.	Frame-mounted fairing: Install headlamp. See service manual.
2.	Install outer fairing. See service manual.
3.	Install main fuse. See service manual.
4.	Install left side cover. See service manual.
5.	Install left saddlebag. See service manual.
6.	Enable HomeLink® module using special tool. Contact a Harley-Davidson dealership. Special Tool: DIGITAL TECHNICIAN II (HD-48650) a. HomeLink® is enabled from the Infotainment Control Unit (IFCU) Configuration menu.