0/0
FORGED TOURING WHEEL 19 IN. FRONT
941004052024-07-03
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
43300955, 43300956, 43300964
Safety glasses
(1) Only simple tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Front Forged Wheels
Table 2. Kit Contents: Front Forged Wheel Kits
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Wheel
Not sold separately
Items mentioned in text, but not included in kit
A
2
Original Equipment (OE) Bearing, regular, Table 3
B
1
OE Bearing, ABS***, Table 3
C
1
OE Axle sleeve, Table 3
D
1
OE Axle sleeve, Table 3
E
1
OE Axle sleeve, Table 3
F
1
OE Axle sleeve, Table 3
L
1
OE Valve stem, Table 3
Table 3. FRONT 25 mm Bearing ABS Wheel Installation Kit (41454-08B)
FRONT 25 mm Bearing ABS Wheel Installation Kit (41454-08B)
ITEM (Quantity Used and Description)
Fitment
Wheel Size
A
B
C
D
J
K
L
M
N
2008 Touring and 2009 and later FLHRC with ABS
16 x 3.0 in
1
1
0
1
0
**
*
*
0
2009 and later Touring with ABS
17 x 3.0 in
1
1
0
1
0
0
*
*
*
2008 and later Touring with ABS
18 x 3.5 in
1
1
0
1
**
**
*
*
*
2012 and later Dyna with ABS (Except FLD, FXDWG and FXDF)
19 x 2.5 in
1
1
1
0
**
0
*
*
0
2008 and later VRSCAW, VRSCD, VRSCF and VRSCDX with ABS
19 x 3.0 in
1
1
1
0
**
**
*
*
0
2009 and later Touring with ABS
19 x 3.5 in
1
1
0
1
0
0
*
*
*
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
* See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
** See NOTES for your wheel kit above the wheel assembly step in INSTALLATION to determine which bearing shim to use for your particular wheel kit and fitment.
*** Red side of bearing must be installed toward the wheel. The ABS bearing is the primary bearing.
**** Bearing shim installed under the primary bearing.
A
Bearing, regular
9276A
B
Bearing, ABS***
9252
C
Axle sleeve
41748-08
D
Axle sleeve
41900-08
J
Bearing shim****
41450-08
K
Bearing shim****
43903-08
L
Valve stem, short
43157-83A
M
Valve stem, long
43206-01
N
Valve stem, pull through
40999-87
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
NOTE
Accessory hub caps are not compatible with this wheel.
Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer:
Wheel Installation Kit (See Table 1 and Table 2 to determine required installation kit.)
  • Two Brake Discs: stock/raw (Part no. 41500158), accessory (Part no. 41500215) or see P&A Retail Catalog.
  • Ten Brake bolts (Part no. 41500196).
Wheel Bearing Remover and Installer (Part no. 94134-09).
If installed in vehicles with Tire Pressure Monitoring System (TPMS):
  • Japan models only (Part no. 42300143)
  • ALL models except Japan (Part no. 42300142)
The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning:
  • Chrome Clean & Shine (93600031 (US) / 93600082 (International))
  • Glaze Poly Sealant (93600026 (US) / 93600079 (International))
  • Harley® Wheel and Spoke Brush (43078-99)
  • Wheel & Tire Cleaner (93600024 (US) / 93600076 (International))
  • Harley® Preserve Bare Aluminum Protectant (99845-07)
WARNING
Install only wheels and installation kits approved for your model motorcycle. Contact a Harley-Davidson dealer to verify fitment. Mismatching wheels and installation kits or installing wheels not approved for your model can cause loss of control, which could result in death or serious injury. (00610c)
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
REMOVE
1. Remove existing front wheel assembly. See service manual.
a. Retain axle, axle nut and wheel spacers for kit installation.
INSTALL
NOTICE
Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c)
1. Install Tire Pressure Monitoring System (TPMS) assembly (L) on wheel. See service manual.
NOTE
Bearing shims provided in installation kits are not required. Discard.
2. Assemble wheel installation kit components and brake disc(s) to wheel, using appropriate service parts table. See service manual.
NOTE
Install primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER.
  • Left side of wheel has DOT markings to identify primary bearing side.
  • Install tire wheel. See service manual.
  • Balance wheel and tire assembly. See service manual.
3. Install front wheel (1), stock axle and stock axle nut. See service manual.
MAINTENANCE AND CLEANING
Parts must be maintained regularly so that they keep their original shine and luster.
1. Clean heavily soiled wheel surfaces using Wheel & Tire Cleaner, applied with Harley Wheel and Spoke Brush.
2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Chrome Clean & Shine.
3. After cleaning and polishing, seal the finish with HARLEY GLAZE POLISH AND SEALANT.