FXSTD Passenger Backrest and Luggage Rack
J015392006-10-09
GENERAL
Kit Number
51114-00, 51144-02, 51534-02, 52549-00, 53806-00, 52050-00
Models
For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
NOTE
A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer.
INSTALLATION
Passenger Upright
| 1. | Unscrew the captive screw fastening the seat rear bracket to the fender. | |||||||||
| 2. | Remove the rubber plugs from the three holes in the rear fender where the passenger upright installs. | |||||||||
| 3. | See Figure 2. Fasten the studplate (2) to the fender (A) with the backing plate (3) and three flange locknuts (4). | |||||||||
| 4. | See Figure 1. Fasten the passenger upright (3) to the studplate (1) with three flange locknuts (2). | |||||||||
| 5. | Insert the seat front bracket into the frame, then fasten the seat rear bracket to the fender. NOTE The seat must be temporarily bowed up in the center to fit the seat rear bracket through the slot in the passenger upright. | |||||||||
 WARNINGAfter installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) WARNINGAfter installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) | ||||||||||
| 6. | Kit 51144-02 only. See Figure 2. Carefully clean the lower hole (B) on the passenger upright (1) with isopropyl alcohol to remove any grease or dirt. Remove backing from adhesive emblem (5) and press the emblem firmly in to place. NOTE When temporarily removing the passenger upright, the mounting and backing plates may be left in place to simplify passenger-upright re-installation. Thread the flange nuts back onto studs to store the nuts. | 
Figure 1. Passenger Upright, Backrest Pad and Luggage Rack Installation |
Backrest Pad
See Figure 2. Fasten the backrest pad (7) to the passenger upright (1) using the button-head screw (6) as shown.
Luggage Rack
NOTE
See Figure 2. Fasten the luggage rack (8) to the backrest with the backrest pad (7) removed from the studplate (2).
Fasten the luggage rack (8) to the passenger upright (1) using the luggage-rack mounting plate (11), button-head screw (12), washer (10), and locknut (9) as shown.
SERVICE PARTS
Figure 2. Service Parts: FXSTD Backrest and Luggage Rack
Table 1. Service Parts Table
Kit | Item | Description (Quantity) | Part Number |
|---|---|---|---|
Kit 51114-00 and 51144-02 | 1 | Passenger upright | Not sold separately |
2 | Stud plate | Not sold separately | |
3 | Backing plate | Not sold separately | |
4 | Flange locknut (6) | 7601 | |
5 | Emblem (kit 51144-02 only) | 14448-94 | |
Kit 51534-00, 52549-00 and 52050-00 | 6 | Screw, button head, 5/16-18 x 3/4 inch | 94393-92T |
7 | Backrest pad | Not sold separately | |
Kit 53806-00 | 8 | Luggage rack | Not sold separately |
9 | Locknut (2) | 7778 | |
10 | Washer (2) | 6701 | |
11 | Luggage rack mounting plate | 53808-00 | |
12 | Screw, button head (2) | 4098 | |
Items mentioned in text, but not included in kit: | |||
A | Rear fender | ||
B | Note: Lower hole found only in kit 51144-02 | ||