1. | Wait for cooling system to completely cool down. | |||||||||||
2. | See the Service Manual. Remove outer (cosmetic) airbox cover and remove upper and lower halves of air filter housing. Save components for installation. | |||||||||||
WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) WARNING Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) | ||||||||||||
3. | Disconnect the battery cables, negative cable first. NOTE It is not necessary to drain the cooling system however, a small amount of coolant will escape when removing hoses. After installing new braided hoses, top off the cooling system using specifications from applicable Service Manual. | |||||||||||
4. | See Figure 1. Remove the clamp screw securing the cooling lines to the engine (near the battery) and remove the clamp. Save screw and clamp for installation. |
Figure 1. Remove Cooling Line Clamp and Screw | ||||||||||
5. | See Figure 2. Loosen the lower worm drive screw and remove the lower coolant hose clamp. Save clamp for installation. NOTE When performing the following step, the decorative (chrome) coolant hose cover will be removed with the hose clamp. | |||||||||||
6. | Loosen the worm drive screw and remove the upper hose clamp and decorative cover. Save for installation. |
Figure 2. Remove Cooling Line Clamp and Screw | ||||||||||
7. | See Figure 3. Using a knife, cut a slit down the upper plastic shrink tube and remove the shrink sleeve. Using a twisting motion (cut hose, if necessary), remove the hose ends from line tubes. Discard hose. | Figure 3. Cut and Remove Shrink Sleeve | ||||||||||
8. | See Figure 4. Loosen worm drive screws and remove upper and lower clamps from inner (short) hose. Use knife and cut hose in half to remove. Discard hose. |
Figure 4. Remove Inner Hose Upper and Lower Clamps | ||||||||||
9. | See Figure 7. Obtain new worm drive Clamp (3) and Decorative Cover (4) from kit. Tighten clamp to decrease diameter until clamp will fit into decorative cover as shown. Loosen clamp until clamps rounds out fully on inside of cover as shown. (with clamp adjuster extending from cut-out). Perform the same procedure for the remaining cover and clamp. | |||||||||||
10. | Obtain new Inner Hose (2) from kit. Slide the decorative cover (with clamp) over one end of hose until hose butts up against end of cover. NOTE When performing the next few steps, it will be necessary to relocate (move) the coolant (metal) lines away from the inlet/outlet tubes to provide room for installing hose. Be extremely careful not to bend or kink metal coolant lines when relocating. | |||||||||||
11. | See Figure 5. Orient hose with decorative cover at bottom. Use coolant to lubricate end and install hose onto inlet tube. Twist while pushing downward until hose slides as far down onto tube as possible. At the top of frame, lightly lubricate hose with coolant and install the coolant line tube into top of hose. Twist hose assembly while pushing tube into hose as far as down as possible. NOTE One stainless clamp (removed in Step 5) and two black clamps (removed in Step 8) are left from removing the original hoses. It is up to you which of the clamps you prefer to use to secure upper portion of the inner braided hose. | |||||||||||
12. | Install one of the saved hose clamps so that clamp is even with top of hose to secure the hose to the coolant line tube (coming from radiator). | |||||||||||
13. | Rotate decorative cover on bottom and hose clamp on top so that clamps are positioned on inner side of braided line (least visible). | |||||||||||
14. | Tighten upper and lower hose clamps securely. | |||||||||||
15. | See Figure 5 and Figure 7. Obtain longer braided hose (1) and remaining Worm Drive Clamp (3) and Decorative Cover (4) assembled during Step 9. |
Figure 5. Install Braided Hoses and Clamps | ||||||||||
16. | Slide the decorative cover onto one end of the hose until the hose butts up completely against the end of the cover. | |||||||||||
17. | Refer to Figure 5. Use coolant and lightly lubricate the inside of the end of hose. Orient hose with decorative cover at bottom as shown and install hose onto inlet tube. Twist while pushing downward until hose slides as far down onto tube as possible. Do not tighten worm drive clamp. | |||||||||||
18. | Use coolant and lightly lubricate the opposite end of hose and install the coolant line tube into top of hose. Twist hose assembly while pushing tube into hose as far as down as possible. | |||||||||||
19. | Orient lower decorative cover and hose clamp so clamp is on inner side of hose (least visible). | |||||||||||
20. | See Figure 6. Install upper hose clamp with decorative cover (removed in Step 2) and align so cover is straight. Tighten hose clamp securely. | Figure 6. Install Upper Clamp and Cover | ||||||||||
WARNING Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) | ||||||||||||
21. | Install the battery cables, positive cable first. | |||||||||||
22. | See the Service Manual. Install upper and lower halves of air filter housing. | |||||||||||
23. | See the Service Manual. Top off the cooling system according to specifications. | |||||||||||
24. | See the Service Manual. Install outer (cosmetic) airbox cover. |
Item | Description (Quantity) | Part Number |
---|---|---|
1 | Hose, inlet (braided stainless) | 26793-01 |
2 | Hose, outlet (braided stainless) | 26794-01 |
3 | Clamp, cosmetic hose (2) | 26795-01 |
4 | Sleeve, decorative clamp (2) | 26796-01 |