REAR SADDLEBAG GUARDRAILS
J020182015-06-02
GENERAL
Kit Number
49087-01, 49088-01
Models
For model fitment information, see the P&A Retail Catalog or harley-davidson.com (English only).
Installation Requirements
Separate purchase and installation of additional parts or accessories may be required for proper installation of this kit on your model motorcycle. See the P&A Retail Catalog or harley-davidson.com (English only) for a list of required parts or accessories for your model.
WARNINGRider and passenger safety depend upon the correct installation of this kit.
If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation.
Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation.
INSTALLATION
Kit Number 49087-01
| 1. | Remove and save fasteners that retain saddlebag guardrails. | |
| 2. | Replace stock saddlebag guardrails with new guardrails from kit. | |
| 3. | Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Tighten each screw to 25.7 N·m (19 ft-lbs). b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Tighten each screw to 12.2 N·m (9 ft-lbs). |
For Domestic FLHRC/I Vehicles Only. (Does not
apply to Harley Davidson International (HDI)
vehicles):
WARNINGFederal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b)
- See Service Parts illustration. Position reflector so it is centered on the vertical portion of the saddlebag guard 2.5 cm (1 in) above the top end of the lower bend where the radius turns upward. Measure and use a small piece of tape to mark location for attachment of the lower edge of the reflector at the 2.5 cm (1 in) mark.
- Remove protective tape backing from one reflector. Locate reflector above the 2.5 cm (1 in) mark. Apply reflector, using even pressure by rubbing back and forth on reflector. Repeat on other side.
NOTE
Reflectors are specific for each side. Reflectors have a flat end and a curved end. The curved end goes down. Top edge should be horizontal when positioned on guard. If not, reflector is for opposite side.
Kit Number 49088-01
| 1. | Remove and save fasteners that retain saddlebag guardrails. | |
| 2. | Replace stock saddlebag guardrails with new guardrails from kit. | |
| 3. | Using four hex socket button head screws (8) removed earlier, attach saddlebag guards using the remaining two existing holes in each guardrail. | |
| 4. | Install and tighten each stock fastener. a. Four stock screws, Part No. 3678, using two new locknuts (5), Part No. 7667. Tighten each screw to 25.7 N·m (19 ft-lbs). b. Two stock screws, Part No. 3601 using two new locknuts (6), Part No. 7686. Tighten each screw to 12.2 N·m (9 ft-lbs). |
SERVICE PARTS
Figure 1. Rear Saddlebag Guardrails
Table 1. Service Parts
Item | Description (Quantity) | Part Number |
|---|---|---|
Rear Saddlebag Guardrail Kit 49087-01 | ||
1 | Locknut (2) | 7667 |
2 | Locknut (2) | 7686 |
3 | Guard assembly, rear, right | 49085-01 |
Guard assembly, rear, left (not shown) | 49082-01 | |
4 | Reflector, red, right | 59370-98 |
Reflector, red, left (not shown) | 59371-98 | |
Rear Saddlebag Guardrail Kit 49088-01 | ||
5 | Locknut (2) | 7667 |
6 | Locknut (2) | 7686 |
7 | Guard assembly, rear, right | 49084-01 |
Guard assembly, rear, left (not shown) | 49081-01 | |
8 | Hex socket screw (4) (not included in kit) | 3584 |
Items mentioned in text. | ||
A | Warning label | |
B | Distance: 1 in (2.5 cm) | |