1 | Right side mirror cover |
2 | Left side mirror cover |
3 | Chrome wire collar (2) |
4 | Adapter harness, 2006 and later models (2) |
5 | Adapter harness, 2005 and earlier models |
6 | Three-way female connector (2) |
7 | Alcohol pad |
8 | Primer tube |
1. | Remove the outer fairing per the instructions in the service manual. Lay the fairing face down on a sturdy work surface. | |||||||||||||
2. | See Figure 2. Remove the mirrors (2), flange nuts (3) and plastic backing plates (4) securing the mirrors to each side of the inner fairing (1), and retain all items | |||||||||||||
3. | Measure 25 mm (1 in) straight down (5) from the large mirror stud hole in the inner fairing, and make a mark. | |||||||||||||
4. | Drill a 6 mm (¼ in) diameter hole (6) through the inner fairing at the mark. | |||||||||||||
5. | See Figure 1. Obtain a chrome wire collar (3) from the kit, and press it into the new hole from the outside of the inner fairing. Gently tap into place with a soft-faced hammer. | |||||||||||||
6. | Repeat Steps 3 through 5 on the opposite side of the inner fairing. NOTE Ambient temperature should be at least 10 °C (50 °F) for proper adhesion of the mirror cover to the mirror. | |||||||||||||
7. | Clean the back surface of the mirrors with the alcohol pad (7) provided. Allow to dry thoroughly. | |||||||||||||
8. | Obtain the primer tube (8) from the kit, and follow the instructions on the tube to activate the primer. When the primer is activated apply the primer to the back surface of one mirror. NOTE The Illuminated Chrome Mirror Covers are side-specific. The covers install with the wire harness exiting from the bottom. |
Figure 2. Fairing Drill for Illuminated Mirror | ||||||||||||
9. | Obtain the correct mirror cover from the kit. Rub the liners on the three pads on the back surface of the mirror cover to activate the adhesive, then remove the liners. | |||||||||||||
10. | Place the mirror cover over the back surface of the mirror and press into place for a minimum of 60 seconds. | |||||||||||||
11. | Repeat Steps 8 through 10 for the remaining mirror and cover. NOTE The plastic backing plates (removed earlier) are identified with a letter "L" (left) or "R" (right) stamped on the post. The mirrors are marked with a letter "L" or "R" stamped on the swivel block. Use the correct backing plate for each mirror by matching the letters. | |||||||||||||
12. | Position the mirror on the outer face of the inner fairing, with the rounded side of the mirror outboard and the Bar & Shield logo upright. a. Insert the mirror cover wiring harness through the chrome wire collar installed in Step 5. b. Insert the mirror post through the original mirror mounting hole. c. Place the correct plastic backing plate against the inner face of the inner fairing, engaging the two holes in the backing plate with the threaded stud and index pin on the mirror swivel block. d. Install the flange nut on the threaded stud and tighten to 3.4–4.5 N·m (30–40 in-lbs). e. Repeat for the remaining mirror on the other side of the fairing. |
1. | See Figure 3. Locate and un-mate the four-way Multilock left [31L] and right [31R] turn signal connectors (9 and 10), found near the left and right inner fairing support braces. |
Figure 3. Wiring Diagram, Illuminated Chrome Mirror Cover Kit (2006 and Later) | ||||||||||||||||||||
2. | Obtain the two adapter harnesses (3) with white four-way connectors (6 and 7) from the kit. Mate the connectors of one adapter harness to the Multilock connectors of circuit [31L] until they click into place. Mate the connectors of the second adapter harness to the Multilock connectors of circuit [31R] until they click into place. | |||||||||||||||||||||
3. | Obtain the two small three-way female connectors (4) from the kit, and mate them to the three-way male connectors (5) on the adapter harnesses until they click into place. | |||||||||||||||||||||
4. | Select the red terminated wire from the left-side mirror cover (2), and push the terminal into the female connector cavity across from the violet wire on the left-side adapter harness until it clicks into place. Select the black terminated wire from the left-side mirror cover, and push the terminal into the female connector cavity across from the black wire on the left-side adapter harness until it clicks into place. The third cavity remains empty in both halves of the connector. | |||||||||||||||||||||
5. | Repeat Step 4 for the right-side mirror (1). |
1. | See Figure 4. Locate and un-mate the six-way Multilock turn signal connector [31] (9), found near the left inner fairing support brace. |
Figure 4. Wiring Diagram, Illuminated Chrome Mirror Cover Kit (1996 Through 2005) | ||||||||||||||||||
2. | Obtain the adapter harness (3) with the white six-way connectors (6 and 7) from the kit. Mate the white six-way connectors of the adapter harness to the Multilock connectors of circuit [31] until they click into place. | |||||||||||||||||||
3. | Obtain the two small three-way female connectors (4) from the kit, and mate them to the three-way male connectors (5) on the adapter harness until they click into place. | |||||||||||||||||||
4. | Select the red terminated wire from the left-side mirror cover (2), and push the terminal into the female connector cavity across from the violet wire on the short branch of the adapter harness until it clicks into place. Select the black terminated wire from the left-side mirror cover, and push the terminal into the female connector cavity across from the black wire on the short branch of the adapter harness until it clicks into place. The third cavity remains empty in both halves of the connector. | |||||||||||||||||||
5. | Repeat Step 4 for the right-side mirror (1), using the connector on the long branch of the adapter harness. |
1. | Secure all wiring away from any moving parts, pinch points or extreme heat. NOTE Verify that the ignition/light key switch is in the OFF position before installing the main fuse/attaching the battery cables. | |
2. | Models with main fuse: Refer to the service manual and follow the instructions given to install the main fuse. Models with main circuit breaker: Apply a light coat of Harley-Davidson electrical contact lubricant (Part Number 99861-02), petroleum jelly or corrosion retardant material to the negative battery terminal. Refer to the service manual and follow the instructions given to attach the negative battery cable. | |
3. | Turn the ignition/light key switch to IGNITION, but do not start the motorcycle. Test for proper turn signal and mirror cover lamp operation. Proper operation of mirror cover lamps is: a. Mirror cover lamps are not lit during normal vehicle operation. b. The proper mirror cover lamp flashes along with the corresponding turn signal when activated. c. BOTH mirror cover lamps flash when the emergency flashers are activated. | |
WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) | ||
4. | Refer to the service manual, and follow instructions to install the seat. | |
5. | Install the outer fairing per the instructions in the service manual. Adjust the mirrors for proper field of vision and compliance with local regulations. |