0/0
IPOD/NAVIGATION CONNECTOR
J051812011-10-03
GENERAL
Kit Number
69200033
Models
This Connector Kit is used to enable the installation of Boom! Audio interface modules on motorcycles without a Non-Ultra Overlay Harness (Part No. 70169-06) installed. See the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for the applicable Interface Module Kits and model fitment information.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Kit Contents
See Figure 2 and Table 1.
PREPARATION
NOTE
For vehicles equipped with security siren:
  • 2007 and later: Verify that the Hands-Free Fob is present.
  • 2006 and earlier: Disarm the siren with the key fob.
  • ALL vehicles: Turn the ignition key switch to IGNITION.
PREPARATION
NOTE
For vehicles equipped with security siren:
  • Verify that the Hands-Free Fob is present.
  • Turn the ignition key switch to IGNITION.
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
  1. See the service manual and remove the main fuse.
  2. Remove the outer fairing and windshield per the service manual.
INSTALLATION
  1. Install the Boom! Audio interface module kit up to the point where six-way connectors [6A} and [6B] have been separated.
  2. See Figure 1 and Figure 2. Get the components of this kit, and the iPod/NIM harness from the Boom! Audio interface module kit.
    3. NOTE
    The terminals are different at each end of the two wires in the harness (3) from this kit, and are identified in Figure 2 as (A) and (B).
  3. Follow instructions in the service manual appendix to remove the seal plugs from cavities 4 and 5 of the 6-way socket housing [6B] on the vehicle interconnect harness. Insert the (B) terminal of the yellow/orange wire into cavity 4 of socket housing [6B]. Insert the (B) terminal of the yellow/violet wire into cavity 5.
  4. Follow instructions in the service manual appendix to insert the (A) terminal of the yellow/orange wire into cavity 13 of the 35-way connector (1). Insert the (A) terminal of the yellow/violet wire into cavity 14.
  5. Insert the five terminated wires from the ipod/NIM harness into the 35-way connector (1) as follows:
  • Insert the red/blue wire terminal into cavity 4.
  • Insert the tan/red wire terminal into cavity 8.
  • Insert the violet/gray wire terminal into cavity 19.
  • Insert the black/blue wire terminal into cavity 27.
  • Insert the tan/blue wire terminal into cavity 31.
  1. Insert a seal plug (2) into each of the unused cavities of the 35-way connector, which will now be known as connector [28B].
    2. NOTE
    Be sure to check that all socket terminals are fully seated and locked into the 35-way socket housing [28B] before plugging back into the radio.
  2. Mate the six-way connectors [6A] and [6B] of the iPod/NIM harness to connectors [6B] on the vehicle interconnect harness and [6A] on the vehicle audio harness.
  3. Continue with the Boom! Audio interface module kit installation per the instructions in that kit.
Figure 1. Wiring Diagram, iPod/Navigation Interface Connector Kit
IN USE
the speaker selector switch should be in the "a" (illuminated) rearward position to hear navigation prompts over the vehicle speakers.
SERVICE PARTS
Figure 2. Service Parts, iPod/Navigation Interface Connector Kit
Table 1. Service Parts
Item
Description (Quantity)
Part Number
1
Socket housing, 35-way
72384-06BK
2
Seal plug (31)
72397-98
3
Wire harness, iPod/NIM jumper
Not sold separately
Items mentioned in text, but not included in kit.
A
Socket terminal 72381-98 (2)
B
Socket terminal 72191-94 (2)
C
Interconnect harness on vehicle
D
Audio harness on vehicle