0/0
SPECTRA GLO LED R/G/B STAGE I SPEAKER LIGHT KIT
J063312016-10-06
Kit Numbers
68000232
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Separate purchase of Harley-Davidson LED Controller Kit (Part No. 68000218 ), if not already installed.
Separate purchase of Three-way Wire Harness (Part No. 69201594 ) may be needed if installing multiple sets of RGB lighting kits.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Spectra Glo light pods are designed and intended for display use only. Some local regulations prohibit using colored or indirect lighting during vehicle operation on public streets. Check local regulations before installation.
Electrical Overload
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
WARNING
When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
Kit Contents
See Figure 31. and Table 1.
INSTALLATION
Motorcycles with a main fuse
1. See service manual. Remove main fuse.
Upper Fairing FLH Model
1. If Controller Kit (Part No. 68000218) is not installed, install now following instructions in that kit.
2.
NOTE
Use caution when working with tweeters and grilles. These components are delicate and can be damaged if mishandled.
See service manual. Remove upper fairing speakers enclosures. Speaker can remain in the enclosure for light engine installation.
3. See Figure 1. Remove protective paper (6) from foam tape (5) on back of light engine (1).
1Light engine
2Connector
3Set screw (4)
4Cable
5Foam tape
6Protective paper
Figure 1. LED Light, Round Stage I Speaker
4.
NOTE
Wipe clean the mounting surface area of the tweeter.
See Figure 2. Place light engine (1) on tweeter (2) as shown. Lightly compress light engine in place.
5.
NOTE
DO NOT over tighten set screws. Over tightening may cause unit damage, tweeter bridge damage, or may render the unit inoperable.
Use the wrench provided. Slowly tighten each set screw (3), alternating one turn at a time, until each set screw just makes contact with tweeter bridge (5). Once all screws make contact with bridge, tighten each screw ¼-½ turn clockwise. This should hold the light engine in place without over-flexing light engine housing.
6. Route cable (4) along tweeter bridge (5) leg. Using the tape in kit, cut to length and secure cable to tweeter bridge.
1Light engine
2Tweeter
3Set screw (4)
4Cable
5Tweeter bridge
Figure 2. FLH Speaker, Tweeter, Tweeter Bridge and LED Light
7. See Figure 3. See service manual. Connect speaker wires to speaker, install speaker enclosure and route light engine cable (1) as shown.
a. See Figure 31. and Table 1. Join connectors from the light engine to RGB three-way wire harness (8).
b. Stabilize the connectors, secure light engine cable and RGB harness with cable straps as needed.
c. Route three-way wire harness toward steering head.
1Light engine cable
2Left speaker pod
3Right speaker pod
Figure 3. FLH Fairing
8.
NOTE
See Instruction Sheet J06266, Spectra Glo Controller and Remote FOB, for installing multiple RGB products.
See Figure 31. and Table 1. Connect and route 48-in. harness (12) from LED R/G/B controller through the wire trough and up the back bone.
9. See Figure 4. Route the end of 48-in. harness to steering head (1). Use caddy (2) to secure harness.
1Steering head
2Caddy
Figure 4. Steering Head
10. See Figure 31. and Table 1. Route light engine cable from speaker to steering head and connect to the 48-in. harness (12) at steering head using 3-way harness (8).
11. Bundle the harnesses from the controller and speakers. Secure the harnesses with cable straps.
12. Repeat steps for opposite speaker and RGB light.
13. Install outer fairing. See the service manual.
Upper Fairing FLTR Model
1. If Controller Kit (Part No. 68000218) is not installed, install now following instructions in that kit.
2.
NOTE
Use caution when working with tweeters and grilles. These components are delicate and can be damaged if mishandled.
See service manual. Remove outer fairing and speaker grilles. Speaker can remain in the enclosure for light engine installation.
3. See Figure 5. Remove protective paper (6) from foam tape (5) on back of light engine (1).
1Light engine
2Connector
3Set screw (4)
4Cable
5Foam tape
6Protective paper
Figure 5. LED Light, Round Stage I Speaker
4.
NOTE
  • Wipe clean the mounting surface area of the tweeter.
  • The left light engine should be positioned on the tweeter so that the cable exits at the 1 o'clock position and the right light engine cable exits at the 11 o'clock position.
See Figure 6. Place light engine (1) on tweeter (2) as shown. Lightly compress light engine in place.
5.
NOTE
DO NOT over tighten set screws. Over tightening may cause unit damage, tweeter bridge damage, or may render the unit inoperable.
Use the wrench provided. Slowly tighten each set screw (3), alternating one turn at a time, until each set screw just makes contact with tweeter bridge (5). Once all screws make contact with bridge, tighten each screw ¼-½ turn clockwise. This should hold the light engine in place without over-flexing light engine housing.
6.
NOTE
The left light engine cable exits at the 12 o'clock position and the right light engine cable exits at the 11 o'clock position.
Route cable (4) toward the top of the speaker and exit cable toward the front of the vehicle (behind speaker pod). Secure to bridge leg with two-sided tape from kit. Route cable and harnesses toward steering head.
1Light engine
2Tweeter
3Set screw (4)
4Cable
5Tweeter bridge
Figure 6. FLTR Left Fairing Speaker
7. See Figure 7. Route light engine cable (1) as shown.
a. See Figure 31. and Table 1. Join connectors from the light engine to RGB three-way wire harness (8).
b. Stabilize the connectors, secure light engine cable and RGB harness with cable straps as needed.
c. Route three-way wire harness toward steering head.
1Light engine cable
2Left speaker pod
3Right speaker pod
Figure 7. FLH Fairing Shown, FLTR Cable Routing is Similar
8.
NOTE
See Instruction Sheet J06266, Spectra Glo Controller and Remote FOB, for installing multiple RGB products.
See Figure 31. and Table 1. Connect and route 48-in. harness (12) from LED R/G/B controller through the wire trough and up the back bone.
9. See Figure 8. Route end of 48-in. harness to steering head (1). Use caddy (2) to secure harness.
1Steering head
2Caddy
Figure 8. Steering Head
10. See Figure 31. and Table 1. Route light engine harness from speaker to steering head and connect to the 48-in. harness (12) at steering head using 3-way harness (8).
11. Bundle the harnesses from the controller and speakers. Secure the harnesses with cable straps.
12. Repeat steps for opposite speaker.
13. Install outer fairing and speaker grille. See the service manual.
Lower Fairing
1. If Controller Kit (Part No. 68000218) is not installed, install now following instructions in that kit.
2.
NOTE
Use caution when working with tweeters and grilles. These components are delicate and can be damaged if mishandled.
See service manual. Remove lower fairing speakers. Retain hardware for later use.
3. See Figure 9. Remove protective paper (6) from foam tape (5) on back of light engine (1).
1Light engine
2Connector
3Set screw (4)
4Cable
5Foam tape
6Protective paper
Figure 9. LED Light, Round Stage I Speaker
4.
NOTE
Wipe clean the mounting surface area of the tweeter.
See Figure 10. Place light engine (1) on tweeter (2) as shown. Lightly compress light engine in place.
5.
NOTE
DO NOT over tighten set screws. Over tightening may cause unit damage, tweeter bridge damage, or may render the unit inoperable.
Use the wrench provided. Slowly tighten each set screw (3), alternating one turn at a time, until each set screw just makes contact with tweeter bridge (5). Once all screws make contact with bridge, tighten each screw ¼-½ turn clockwise. This should hold the light engine in place without over-flexing light engine housing.
6. Route the cable (4) along tweeter bridge (5) leg. Using the tape in kit, cut to length and secure cable to back of tweeter bridge.
1Light engine
2Tweeter
3Set screw (4)
4Cable
5Tweeter bridge
Figure 10. Speaker, Tweeter, Tweeter Bridge and LED Light
7. See service manual. Remove lower fairing cap.
8. See Figure 11. Mark location for pilot hole on outboard side of lower fairing.
a. Start point for dimension line (1) (back of lower fairing).
b. Make a mark at 2 in (50.4 mm)
c. Start point for dimension line (3) (inside bend).
d. Make a mark at 4 in (101.6 mm)
9. Drill a 1/8 in pilot hole.
10. Use a step drill to increase 1/8 in hole to 5/8 in. hole.
1Start point for dimension line
22 in. (50.4 mm)
3Start point for dimension line
44 in. (101.6 mm)
5Grommet
6Harness
Figure 11. Left Lower Fairing Shown
11. See Figure 31. and Table 1. Slide the grommet about 6 in (15 cm) from the end of the harness (10).
12. Install harness with grommet in hole of lower faring. Press the grommet into the hole by first starting one tapered edge of the grommet into the hole. Correctly installed the outside of the grommet should seat against the faring. Press around the perimeter of the grommet to seat it in place.
13. See service manual. Install speaker in lower faring.
a. See Figure 12. Join connectors (4) from the light engine to RGB harness.
b. Route light engine cable (3) along the back of the speaker (1) as shown. To stabilize the connectors (4), secure light engine cable (3) and RGB harness (5) with cable straps (2) as shown.
c. Connect speaker wires to speaker and position in speaker box.
d. Install grille and screws for speaker.
1Speaker
2Cable strap
3Cable
4Connectors
5RGB Harness
Figure 12. Speaker Back, Cable and Cable Tie
14.
NOTE
Adjust extra RGB harness slack as needed.
Route harness toward the frame using the engine guard.
15. See service manual. Install faring cap.
16.
NOTE
See Instruction Sheet J06266, Spectra Glo Controller and Remote FOB, for installing multiple RGB products.
See Figure 31. and Table 1. Connect and route 48-in. harness (12) from LED R/G/B controller through the wire trough and up the back bone.
17. See Figure 13. Route end of 48-in. harness to steering head (1). Use caddy (2) to secure harness.
1Steering head
2Caddy
Figure 13. Steering Head
18. See Figure 31. and Table 1. Route light engine harness from speaker to steering head and connect to the 48-in. harness (12) at steering head using 3-way harness (8).
19. Bundle the harnesses from the controller and speakers. Secure the harnesses with cable straps.
20. Repeat steps for the opposite speaker.
Tour-Pak®
1. If Controller Kit (Part No. 68000218) is not installed, install now following instructions in that kit.
2.
NOTE
Use caution when working with tweeters and grilles. These components are delicate and can be damaged if mishandled.
See service manual. Remove Tour-Pak speakers. Retain hardware for later use.
3. See Figure 14. Remove protective paper (6) from foam tape (5) on back of light engine (1).
1Light engine
2Connector
3Set screw (4)
4Cable
5Foam tape
6Protective paper
Figure 14. LED Light, Round Stage I Speaker
4.
NOTE
Wipe clean the mounting surface area of the tweeter.
See Figure 15. Place light engine (1) on tweeter (2) as shown. Lightly compress light engine in place.
5.
NOTE
DO NOT over tighten set screws. Over tightening may cause unit damage, tweeter bridge damage, or may render the unit inoperable.
Use the wrench provided. Slowly tighten each set screw (3), alternating one turn at a time, until each set screw just makes contact with tweeter bridge (5). Once all screws make contact with bridge, tighten each screw ¼-½ turn clockwise. This should hold the light engine in place without over-flexing light engine housing.
6. Route the cable (4) along tweeter bridge (5) leg. Using the tape in kit, cut to length and secure cable to back of tweeter bridge. Secure cable to back of speaker with cable strap.
1Light engine
2Tweeter
3Set screw (4)
4Cable
6Tweeter bridge
7Screw (4)
Figure 15. Speaker, Tweeter, Tweeter Bridge and LED Light
7.
NOTE
Pull wires away from drilling area.
Drill a 1/8 in pilot hole. Use a step drill to increase 1/8 in hole to 5/8 in.
See Figure 16. Drill a 5/8 in (16 mm) hole (2) in each speaker pod (1), approximately where shown.
8. Lightly sand the speaker housings around the grommet holes.
9. Slide the grommet (4) about 6 in (15 cm) from the end of the harness (3).
10. Insert the male end of the harness with grommet (4). Press the grommet (4) into the hole by first starting one tapered edge of the grommet into the hole. Correctly installed the outside of the grommet should seat against the outside of the speaker pod. Press around the perimeter of the grommet to seat it in place.
1Speaker pod
25/8-in. Hole
324-in. Harness with grommet
4Grommet
Figure 16. Left Speaker Pod
11. See service manual. Install speaker in pod.
a. See Figure 17. Join connectors (4) from the light engine to RGB harness.
b. Route light engine cable (3) along the back of the speaker (1) as shown. To stabilize the connectors (4), secure light engine cable (3) and RGB harness (5) with cable straps (2) as shown.
c. Connect speaker wires to speaker and position in speaker box.
d. Install grille and screws for speaker.
1Speaker
2Cable strap
3Cable
4Connectors
5RGB Harness
Figure 17. Speaker Back, Cable and Cable Tie
12. Repeat steps for the opposite speaker.
13.
NOTE
See Instruction Sheet J06266, Spectra Glo Controller and Remote FOB, for installing multiple RGB products.
See Figure 31. and Table 1. Connect and route 48-in. harness (12) from LED R/G/B controller toward Tour Pak speakers. Connect 3-way harness (8) to speaker connections.
14.
NOTE
Adjust extra RGB harness slack as needed.
Route controller and light kit connectors and harnesses.
15. Bundle the harnesses from the controller and speakers. Secure the harnesses with cable straps.
Saddlebag
1. If Controller Kit (Part No. 68000218) is not installed, install one now following instructions in that kit.
2. See service manual. Remove saddlebags.
3.
NOTE
Unfinished saddlebag covers must be finish painted before speaker installation.
To minimize damage to paint during cutting and drilling. Cover both sides of the area being drilled or cut with masking tape.
Place saddlebag on protected surface with mounting (inboard) side facing up.
4. See Figure 18. Place template (1) on outside front of saddlebag. The template oval holes fit over front latch fasteners (2). Secure the template with tape (4).
5. Drill a 1/8 in pilot hole (3).
6. Remove template. Use a step drill to increase 1/8 in hole to 5/8 in. hole.
1Template
2Front latch fasteners
3Pilot hole
4Tape
Figure 18. Template and Saddlebag
7. See Figure 19. Remove the speaker grille screws (3). Retain for later use.
8. Remove speaker grille (4). Retain for later use.
9. Note location of the rubber washers (1) for reuse.
1Rubber washer
2Grille mount well
3Screw, short (4)
4Speaker grille
Figure 19. Grille Installation and Removal
10.
NOTE
Use caution when working with tweeters and grilles. These components are delicate and can be damaged if mishandled.
Remove four screws, speaker from saddlebag and disconnect harness. Retain hardware for later use.
11. See Figure 20. Remove protective paper (6) from foam (5) tape on back of light engine (1).
1Light engine
2Connector
3Set screw (4)
4Cable
5Foam tape
6Protective paper
Figure 20. LED Light, Saddlebag Stage I Speaker
12.
NOTE
Wipe clean the mounting surface area of the tweeter.
See Figure 21. Place light engine (1) on tweeter bridge (2) as shown. Lightly compress light engine in place.
13.
NOTE
DO NOT over tighten set screws. Over tightening may cause unit damage, tweeter bridge damage, or may render the unit inoperable.
Slowly tighten each set screw (3), alternating one turn at a time, using wrench provided, until each set screw just makes contact with tweeter bridge. Once all screws make contact with bridge, tighten each screw ¼-½ turn clockwise. This should hold the light engine in place without over-flexing light engine housing.
14. Route the cable (4) along tweeter bridge (5) leg. Using the tape in kit, cut to length and secure cable to back of tweeter bridge. Locate area near light engine where wires are separated individually. See Figure 22. Verify this split wire (6) area is located on the speaker gasket. Place a small amount (pea size) of IIR rubber (7) strip over split wires at gasket area. See Figure 24. Secure cable to back of speaker with cable strap (2).
1Light engine
2Tweeter
3Set screw (4)
4Cable
5Tweeter bridge
Figure 21. Light Engine Installation
6Split wire
7IIR Rubber
Figure 22. IIR Rubber
15. See Figure 24. Slide the grommet (6) about 4-1/2 in (11 cm) from the end of the harness (3). This will leave about 4-1/2 in (11 cm) outside the saddlebag once the grommet is installed.
16. Install wire harness (3) with grommet (6). Slide the light engine connector from outside the saddlebag to the inside. Tapered edge of the grommet faces the saddlebag. Press the grommet (6) into the hole by first starting one tapered edge of the grommet into the hole. Correctly installed the outside of the grommet should seat against the outside of the saddlebag. Press around the perimeter of the grommet to seat it in place.
17. See Figure 23. Position tweeter (2) toward the front of the saddlebag as shown. Verify IIR Rubber is between split wire area and saddlebag housing. This should encapsulate the wires and seal speaker cone to saddlebag housing to prevent water intrusion. Connect speaker to harness and secure speaker with screws removed earlier. Alternately tighten screws to:
Torque: 1.1–1.7 N·m (10–15 in-lbs)
1Light engine
2Tweeter
3Set screw (4)
4Cable
5Tweeter bridge
Figure 23. Speaker Installation
18. See Figure 24. Join connectors (1) from the light engine to the harness. Secure harness to speaker near the connection with cable strap (2)
19.
NOTE
Do not obstruct the saddlebag weight capacity warning label (5).
Install two retainer clips (4) to the front panel of saddlebag as shown.
20. Route wires as shown. Open and close the saddlebag lid. Verify there are no obstructions. Secure wires to retainers using cable straps.
1Light connector and harness connector
2Cable strap
3Wire harness
4Retainer clip (2)
5Warning label, saddlebag weight capacity
6Grommet
7Harness to harness connector
Figure 24. Saddlebag Wire Routing
21. Repeat steps for opposite speaker.
22. See Figure 25. Place rubber washers (1) into the grille mount well (2).
1Rubber washer
2Grille mount well
3Screw, short (4)
4Speaker grille
Figure 25. Grille Installation and Removal
23. Verify rubber washers (1) are in place. Place the speaker grille (4) into position over the speaker face. Secure with the four short screws (3). Alternately tighten the screws to:
Torque: 1.1–1.7 N·m (10–15 in-lbs)
24.
NOTE
See Instruction Sheet J06266, Spectra Glo Controller and Remote FOB, for installing multiple RGB products.
See Figure 31. and Table 1. Connect and route 48-in. harness (12) from LED R/G/B controller toward the saddlebags. Connect 3-way harness (8) to speaker connections.
25. Bundle the harnesses from the controller and light engine. Secure the harnesses with cable straps.
Tri Glide® Trike
1. If Controller Kit (Part No. 68000218) is not installed, install now following instructions in that kit.
2.
NOTE
Use caution when working with tweeters and grilles. These components are delicate and can be damaged if mishandled.
Remove screws and body speakers. Retain hardware for later use.
3.
NOTE
Drill a 1/8 in pilot hole.
See Figure 26. From within the speaker pod opening (1), drill a 5/8 in (16 mm) hole (2) in general area of the flat surface.
1Speaker Pod Opening
25/8-in Hole Location
Figure 26. Drill 5/8-in Hole Location
4. Debur holes as needed and clean speaker pods from residual cutting material.
5.
NOTE
Tapered edge of the grommet faces the male end of the harness.
See Figure 31. and Table 1. Slide the grommet about 6 in (15 cm) from the male end of the harness (10).
6.
NOTE
Tapered edge of the grommet faces the inside of the speaker pod when installed.
See Figure 27. From the inboard side of the speaker pod, insert the male end of the harness with grommet (2). Press the grommet into the 5/8 in (16 mm) hole (1) by first starting one tapered edge of the grommet into the hole. Correctly installed the outside of the grommet should seat against the outside of the speaker pod. Press around the perimeter of the grommet to seat it in place.
15/8-in Hole Location
2RGB Harness with Grommet
Figure 27. RGB Harness Installation
7. See Figure 28. Remove protective paper (6) from foam tape (5) on back of light engine (1).
1Light engine
2Connector
3Set screw (4)
4Cable
5Foam tape
6Protective paper
Figure 28. LED Light, Round Stage I Speaker
8.
NOTE
Wipe clean the mounting surface area of the tweeter.
See Figure 29. Place light engine (1) on tweeter (2) as shown. Lightly compress light engine in place.
9.
NOTE
DO NOT over tighten set screws. Over tightening may cause unit damage, tweeter bridge damage, or may render the unit inoperable.
Use the wrench provided. Slowly tighten each set screw (3), alternating one turn at a time, until each set screw just makes contact with tweeter bridge (5). Once all screws make contact with bridge, tighten each screw ¼-½ turn clockwise. This should hold the light engine in place without over-flexing light engine housing.
10. Route the cable (4) along tweeter bridge (5) leg. Using the tape in kit, cut to length and secure cable to back of tweeter bridge.
1Light engine
2Tweeter
3Set screw (4)
4Cable
5Tweeter bridge
Figure 29. Speaker, Tweeter, Tweeter Bridge and LED Light
11. See service manual. Install body speaker.
a. See Figure 30. Join connectors (4) from the light engine to RGB harness.
b. Route light engine cable (3) along the back of the speaker (1) as shown. To stabilize the connectors (4), secure light engine cable (3) and RGB harness (5) with cable straps (2) as shown.
c. Connect speaker wires to speaker and position in speaker pod.
d. Install grille and screws for speaker.
1Speaker
2Cable strap
3Cable
4Connectors
5RGB Harness
Figure 30. Speaker Back, Cable and Cable Tie
12.
NOTE
See Instruction Sheet J06266, Spectra Glo Controller and Remote FOB, for installing multiple RGB products.
See Figure 31. and Table 1. Connect and route 48-in. harness (12) from LED R/G/B controller toward the body speakers. Connect 3-way harness (8) to speaker connections.
13.
NOTE
Adjust extra RGB harness slack as needed.
Bundle the harnesses from the controller and speakers. Secure the harnesses with cable straps.
14. Repeat steps for the opposite speaker.
SERVICE PARTS
Figure 31. Service Parts, Stage I Speaker R/G/B/ LED Light Kits
SERVICE PARTS
Table 1. Service Parts Table
Kit
Item
Description (Quantity)
Part Number
68000232
1
Light, saddlebag, stage I, LED, R/G/B, (2)
68000198
2
Cable strap (10)
10126
3
Wire retainer (4)
11769
4
Rubber strip
Not Sold Separately
5
Tape, two sided
11100181
6
Wrench, hex, 2mm
14900095
7
Template
14900069
8
Wire harness, three-way
69201594
9
End cap
69201597
10
Wire harness, with grommet, 24 in (2)
69201595
11
Wire harness, 24 in (2)
69201530
12
Wire harness, 48 in (2)
69201625
SPECTRA GLO LOAD CALCULATION INFORMATION
The Spectra Glo system is limited to 3000 mA. Use the following table to determine the total current draw of the desired configuration. Calculate the total current dray by multiplying the number of kit(s) (each line) by the provided current draw. Sum all totals. The value should be less than or equal to 3000 mA. The following example describes how to calculate total system load.
Table 2. Calculator Example of Spectra Glo Kits
Kit Name
Kit Part Number
Number of Kits
Current mA
Total
Rider Footboards
50500492
1
500
500
Passenger Footboards
50500495
1
350
350
Fairing Vent
68000194
275
Speaker Lights (Stage I)
68000232
125
Speaker Lights (Stage II Round)
68000231
1
125
125
Speaker Lights (Stage II Saddle Bag)
68000233
125
Base Light Pods (6)
68000213
2
450
900
Expansion Light Pods (4)
68000214
1
300
300
* System Total must be 3000 mA or less.
System Total =
2175
Table 3. Spectra Glo RGB Accessory Calculator
Kit Name
Kit Part Number
Number of Kits
Current mA
Total
Rider Footboards
50500492
500
Passenger Footboards
50500495
350
Fairing Vent
68000194
275
Speaker Lights (Stage I)
68000232
125
Speaker Lights (Stage II Round)
68000231
125
Speaker Lights (Stage II Saddle Bag)
68000233
125
Base Light Pods (6)
68000213
450
Expansion Light Pods (4)
68000214
300
* System Total must be 3000 mA or less.
System Total =
Table 4. Spectra Glo RGB Accessories
Accessories
Part Number
Remote
68000217
JAE Cap
69201597
Y Harness (3-way)
69201594
3-in Jumper Harness
69201525
8-in Jumper Harness
69201529
24-in Jumper Harness
69201530
24-in Jumper w/grommet
69201595
48-in Jumper Harness
69201625