Kits | Suggested Tools | Skill Level(1) |
---|---|---|
52300643, 52300644, 52300645, 52300646 | Safety Glasses, Torque Wrench, Loctite 243 medium strength threadlocker and sealant (blue) |
Item | Qty Kit 52300643, 52300644 | Qty Kit 52300645, 52300646 | Description | Part No. | Notes | |
---|---|---|---|---|---|---|
1 | 2 | Reflectors, red | 59270-10 | |||
2 | 2, Kit 52300643 | Bolts, socket head hex | 94356-91T | |||
2, Kit 52300644 | Bolts, socket head hex, black | 10200576 | ||||
4, Kit 52300645 | Bolts, socket head hex | 94355-91T | ||||
4, Kit 52300646 | Bolts, socket head hex, black | 10200575 | ||||
3 | 2, Kit 52300643 | Bolts, socket head hex | 94357-91T | |||
2, Kit 52300644 | Bolts, socket head hex, black | 10200577 | ||||
4 | 2 | Spacer, docking point, front | 12400141 | FLFB, FXBR: One on each side at front. | ||
5 | 6 | Spacer, docking point | 12400142 | FLFB: Two on each side at rear. One on each side at front. FXBR: One on each side at rear. | ||
6 | 2, Kit 52300643 | 2, Kit 52300645 | Bushing, docking point, front, chrome | 52300649 | ||
2, Kit 52300644 | 2, Kit 52300646 | Bushing, docking point, front, black | 52300650 | |||
7 | 2, Kit 52300643 | 2, Kit 52300645 | Bushing, docking point, rear, chrome | 52300647 | ||
2, Kit 52300644 | 2, Kit 52300646 | Bushing, docking point, rear, black | 52300648 | |||
Items mentioned in text: | ||||||
A | Rotation | |||||
E | Molded in "T" with arrows | |||||
F | 90 degree maximum docking point adjustment range (x2) |
1. | NOTE See the owner's manual for more detailed information regarding main fuse removal. | |
2. | Models with security: a. Verify that fob is present. b. Turn OFF/RUN switch to RUN. | |
3. | Remove fuse cover. a. Remove fuse block from ECM (Electronic control module) sub caddy. b. Remove fuse cover. | |
4. | Remove main fuse. | |
5. | Models with security: Turn ignition switch OFF. |
1. | See Figure 2. FXLR, FLSL, FXFB, FLDE: Remove right side Original Equipment (OE) screws. | |||||||
|
Figure 2. Inner Screws of Four Bolt Pattern | |||||||
2. | See Figure 1. FLFB and FXBR: Remove both right side OE screws. | |||||||
3. | FLFB: Assemble spacers. a. Front: One each thin spacer (5) and thick spacer (4). b. Rear: Two thin spacers (5). c. Refer to section, DOCKING POINT INSTALLATION. | |||||||
4. | FXBR: Assemble spacers. a. Front: One thick spacer (4). b. Rear: One thin spacer (5). c. Refer to section, DOCKING POINT INSTALLATION. | |||||||
5. | See Figure 3. FLHC: Remove right side saddlebag from vehicle. a. Open saddlebag lid. b. Remove OE screws and loose spacers (1) attaching saddlebag to vehicle. c. Separate saddlebag from vehicle. d. Remove threadlocker from OE screws and mounting hole threads. See CLEANING FASTENER THREADS. e. Replace loose spacers (1) with docking points. The plastic docking points (2) in rear end of vehicle. f. Apply threadlocker to fasteners.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) g. Install screw through OE saddlebag and docking points and attach to vehicle. h. Refer to steps 3 through 6 of DOCKING POINT INSTALLATION. |
Figure 3. Replace OE Spacers with Docking Points - FLHC | ||||||
6. | See Figure 4. FLSB, FXLRST: Remove right side saddlebag from vehicle. a. Remove OE screws (3), saddlebag docking points (2) and spacers (1). b. Remove threadlocker from OE screws (3) and mounting hole threads. See CLEANING FASTENER THREADS. c. Discard inner spacers (1) and replace with docking points from kit. The plastic docking point goes in the rear most position. d. Apply threadlocker to fasteners.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) e. Install fasteners through OE saddlebag docking points and P&A docking points to vehicle. f. Refer to steps 3 through 6 of DOCKING POINT INSTALLATION. |
Figure 4. Replace OE Spacer with Docking Point - FLSB, FXLRST |
1. | Remove threadlocker from mounting hole threads. See CLEANING FASTENER THREADS. | |
2. | See Figure 1. Apply threadlocker to bolts (2).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) | |
3. | NOTE If used, spacers are placed between the fender support and docking point. a. Attach spacers, if used, and docking points to vehicle with bolts (2,3). b. Rotate docking point so "T"s are on top and bottom. c. Finger tighten. | |
4. | Repeat DOCKING HARDWARE SET-UP and steps 1-3 of this section for left side. | |
5. | Test fit upright or rack. | |
6. | Adjust docking points. |
1. | FLSB: Remove detachable saddlebags. See owner's manual. | |
2. | See Figure 5. To adjust, rotate (3) in small increments so the "T" (1) is no longer on top and approaches either position (2). | |
3. | At each increment, check fit with accessory. | |
4. | Continue rotation in small increments and test until desired tightness is achieved. The tightest possible position is when the "T"s reach position (2). | |
5. | Tighten docking point screws. Torque: 28.5–37 N·m (21–27 ft-lbs) | |
6. | FLSB: Install detachable saddlebags. See owner's manual. |
1 | Loosest position (T location) |
2 | Tightest position (T location) |
3 | Possible rotation direction |
1. | Record the current "T" position for each docking point. Remove screw from rear docking point. | |
2. | Remove threadlocker from the docking point screws and mounting hole threads, see CLEANING FASTENER THREADS, before applying threadlocker to screw heads. Install docking points, screws and washers. Tighten finger-tight.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) | |
3. | See Figure 5. If "T"s are not in tightest position (2), rotate docking points slightly, moving "T"s toward (2) until a tight fit of the detachable accessory is achieved at each location. | |
4. | Secure docking point screws. Tighten. Torque: 28.5–37 N·m (21–27 ft-lbs) | |
5. | If the docking point "T"s are in position (E): a. Remove screw from rear docking points. b. Rotate each docking point until the "T" on opposite side reaches loosest position (1). c. Remove threadlocker from docking point screws and mounting hole threads, see CLEANING FASTENER THREADS, before applying threadlocker to the screw threads. Install the screws and washers. Tighten finger-tight.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) d. Check detachable accessory at each docking point, rotating the "T" toward (2) until a tight fit of the detachable accessory is achieved at each location. Secure docking point screws. Tighten. Torque: 28.5–37 N·m (21–27 ft-lbs) | |
6. | After multiple adjustments, if the detachable accessory continues to rattle or remains loose, replace the docking points. |