RIDER & PASSENGER FOOTPEG KIT
J065132018-08-21
GENERAL
Kit Number
Rider: 50500870, 50500871, 50500873, 50500874
Passenger: 50500992, 50500993
Trims: 50500937, 50500938, 50500939, 50500940
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer.
INSTALLATION
RIDER
NOTE
On 50500871, 50500874: For Installation on FXBR/S, Remove the long wear peg labeled FXBB, FXLR, FLSB and install the wear peg labeled FXBR.
| 1. | See Figure 2. Your model motorcycle is equipped with a pin (4) and retaining clip (2), remove them and retain for future use. Save all hardware, including torsion spring (1), for installation of the new footpegs (3). |  Figure 1. Torsion Spring | ||||||||||
| 2. | See Figure 2. Insert short leg of torsion spring (1) into hole in new footpeg (3). Align long leg of torsion spring (1) to hole in footpeg mount and insert. Rotate footpeg (3) into position in clevis and insert pin (4) through clevis, footpeg (3) and spring (1). Install retaining clip (2). Repeat on other side. NOTE See Figure 1. When performing the next step, verify that the spring is positioned inside of the footpeg. | |||||||||||
| 3. | See Figure 2. Adjust orientation as follows: a. For forward controls, foot surface to be parallel to the mounting pin. b. For mid controls, foot surface to be parallel to ground. c. Tighten adjustment screw (5). Torque: 28.5 N·m (21 ft-lbs) | 
Figure 2. Rider Footpeg Torsion Spring Installation |
PASSENGER
| 1. | See Figure 3. Your model motorcycle is equipped with a pin (1) and retaining clip (5). Remove them and retain for future use. Save all hardware, including detent spring (3), detent ball (4) and cage (6) for installation of the new footpegs (2). | |||||||||||||||
| 2. | Insert detent spring (3) into new footpeg (2), followed by detent ball (4). Position cage (6) on footpeg clevis edge while capturing the detent ball (4) and detent spring (3) inside cage (6) while sliding cage (6) onto footpeg clevis. NOTE See Figure 3. When performing the next step, verify that the spring (3) is positioned inside of the footpeg (2). | |||||||||||||||
| 3. | Align cage (6) and footpeg (2) with footpeg mount on vehicle. | |||||||||||||||
| 4. | Install pin (1) and retaining clip (5). | |||||||||||||||
| 5. | See Figure 3. Adjust orientation as follows: a. Rotate to desired orientation. b. Fold peg up to stowed position and confirm clearance to other components. Adjust as necessary. c. Tighten adjustment screw (7). Torque: 28.5 N·m (21 ft-lbs) | 
Figure 3. Passenger Footpeg Detent Ball Installation |
WARNINGFootrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a)
REPLACE TRIM or WEAR PEG
| 1. | See Figure 4. Remove two screws (8). | |
| 2. | Replace trim or wear peg (if applicable). | |
| 3. | Apply threadlocker to the screws (8) and install screws (8). Tighten. Torque: 1.69–2.26 N·m (15–20 in-lbs) LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) |
SERVICE PARTS
Figure 4. Service Parts: Footpeg Kit and Insert
Table 1. Service Parts: Footpeg Kit and Insert
Kit | Item | Description (Quantity) | Part Number |
|---|---|---|---|
50500870 50500871 50500873 50500874 | 1 | Rider footpeg clevis, (2) Rider footpeg clevis, short (2) | 50501014 50501112 |
3 | Rider footpeg assembly, black (2) Rider footpeg assembly, bronze (2) | 50500891, 50501082 50500896, 50501084 | |
5 | Footpeg attachment screw (2) | 2708A | |
6 | Footpeg wear peg, black (2) Footpeg wear peg, short (2) | 50500892 50501108 | |
8 | Stainless steel screw (4) | 10200662 | |
50500992 50500993 | 2 | Passenger footpeg clevis, short (2) | 50501121 |
4 | Passenger footpeg assembly short, black (2) Passenger footpeg assembly short, bronze (2) | 50501119 50501120 | |
5 | Footpeg attachment screw (2) | 2708A | |
8 | Stainless steel screw (4) | 10200662 | |
All Kits | 7 | Insert, footpeg, black Insert, footpeg, bronze Insert, footpeg, orange Insert, footpeg, aluminum | 50500937 50500938 50500939 50500940 |