BOOM! PREMIUM RADIO INFOTAINMENT KIT

J066492018-08-22

GENERAL

Dealer installation is recommended.

Kit Number

76000829A, 76000834A

Models

For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).

Installation Requirements

Radio configuration using DIGITAL TECHNICIAN II (Part Number:HD-48650) diagnostic tool is:

Required before audio system OPERATION. System will beep every 3 seconds until configuration is completed.
Only available through authorized Harley-Davidson dealers.

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.

Kit Contents

See Figure 5 and Table 1.

REMOVAL

See service manual for specific instructions on this generalized procedure.

WARNING

To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)

Remove main fuse.

Remove outer fairing.

Fork-Mounted Faring: Remove fairing vent and instrument cluster.

Remove upper support bracket.

4.1.	Fork-Mounted Faring: See Figure 1. Remove screws (1, 2, 3, 6).

1	Upper support-to-speaker enclosure screw (4)
2	Upper support-to-inner fairing screw (2)
3	Upper support-to-radio screw (4)
4	Upper support bracket
5	Instrument cluster
6	Media compartment screw

Figure 1. Fork-Mounted Upper Support Bracket

4.2.	Frame-Mounted Faring: See Figure 2. Remove screws (1).

1	Screw (2)
2	Upper support bracket

Figure 2. Frame-Mounted Upper Support Bracket

See Figure 3. Disconnect connectors (2-5).

Remove four screws (1).

1	Screw, radio mounting (4)
2	Global Positioning System (GPS) connector
3	AM/FM connector
4	Universal Serial Bus (USB) connector
5	Radio harness connector

Figure 3. Radio Connectors

Pull radio up and forward to remove.

INSTALLATION

1.	See Figure 5. Install radio (1). a. Position radio on fairing support brackets and push toward opening in inner fairing.
2.	See Figure 3. Install four screws (1). Torque: 6.8–9.5 N·m (60–84 in-lbs) Radio mounting screw
3.	Fork-Mounted Faring: Install instrument cluster.
4.	Fork-Mounted Faring: See Figure 1. Install upper support bracket. a. Install screws (2). Tighten. Torque: 1.1–2.2 N·m (10–19 in-lbs) b. Install screws (1). Tighten. Torque: 5.4–6.8 N·m (48–60 in-lbs) c. Install screws (3). Tighten. Torque: 2.8–4 N·m (25–35 in-lbs) d. Install screw (6). Tighten. Torque: 2.8–4 N·m (25–35 in-lbs)
5.	Frame-Mounted Faring: See Figure 2. Install upper support bracket. a. Install screw (1). Tighten. Torque: 2.8–4 N·m (25–35 in-lbs)
6.	See Figure 4. Install GPS antenna. a. Clean top of upper support bracket with isopropyl alcohol. Allow to dry completely. b. Remove adhesive backing from antenna. c. With the wire lead toward the right, press and hold antenna (2) for 60 seconds. NOTE After installing antenna, avoid contact or movement of the antenna for 20 minutes.
7.	Secure antenna lead to harness with cable strap (1).
8.	See Figure 3. Connect connectors (2-5).

1	Cable strap
2	GPS antenna
3	Connector

Figure 4. GPS Antenna

SWITCH CAP

1.	NOTE See the service manual of the year and model vehicle that the service is being performed on for the following steps. Remove front right hand control cover.
2.	Remove right turn signal and info switch cap.
3.	See Figure 5. Install new switch cap (2).
4.	Install front right hand control cover.

COMPLETE

NOTE

To prevent possible damage to the audio system, verify that the ignition is OFF before installing the main fuse.

1.	Fork-Mounted Faring: Install fairing vent.
2.	Install outer fairing.
3.	Install main fuse.
4.	Update radio software. See Harley-Davidson.com a. Follow instructions on website.
5.	NOTE Digital Technician II (DT II) will configure the radio and amplifiers all at the same time. Have Harley-Davidson dealer configure the radio using DT II. Special Tool: DIGITAL TECHNICIAN II (HD-48650)
6.	NOTE To download a Portable Document Format (PDF) of the Harley Davidson International (HDI) or Rest of World (ROW) Boom! Box owner's manual, see Harley-Davidson.com or https://serviceinfo.harley-davidson.com. Refer to BOOM! BOX 6.5 GTS owner's manual. a. Turn radio ON. b. Make sure that all speakers are working properly. c. Make sure front/rear fader function is operating correctly.
7.	Verify all turn signals functions are working properly.

SERVICE PARTS

Figure 5. Service Parts, Boom! Premium Radio Infotainment Kit

Table 1. Service Parts

Item	Description		Part Number
1	Premium Radio Infotainment, (DOM)	Fork Mounted Fairing	76000783A
1	Premium Radio Infotainment, (DOM)	Frame Mounted Fairing	76000779A
2	Switch cap		71500478
3	GPS antenna		76000789
4	Boom! Box 6.5 GTS Owner's Manual (Not shown)		94000601
5	Boom! Box 6.5 GTS Quick Start Guide (Not shown)		94000634