0/0
ADVANCED AUDIO SIRIUSXM SATELLITE RADIO KIT
J066612018-08-22
GENERAL
Kit Number
76000842
Models
For the most up-to-date model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
SiriusXM® satellite radio is only available within the continental United States, District of Columbia and Puerto Rico (with limited coverage). It is not available in Alaska or Hawaii. Canadian coverage, contact SiriusXM of Canada directly.
Additional Parts Required
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Electrical Overload
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
WARNING
When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
The SiriusXM Radio requires up to 400 mA additional current from the electrical system.
Kit Contents
Refer to Figure 8 and Table 1.
PREPARE
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
1.
NOTE
See the service manual for the following steps.
Remove main fuse.
2. Remove outer fairing.
INSTALLATION
SiriusXM Module
1. See Figure 1. Remove the access screws (3) at the back of the radio (1). Save access screws for installation.
2. Remove and discard access panel (2).
3. Install SiriusXM module.
a. See Figure 8. If installed, remove plastic pin guard (A) from SiriusXM module (2).
b. See Figure 1. Align connectors of the SiriusXM module and radio.
c. Hold SiriusXM module parallel to radio.
d. Gently slide SiriusXM module straight into position.
e. Confirm that SiriusXM module is properly aligned with the radio. Refer to Figure 2 and Figure 3.
f. Inspect foam seal around entire module for gaps.
4. Install access screws. Tighten.
Torque: 0.34–0.56 N·m (3–5 in-lbs)
1Radio
2Access panel
3Access screw (2)
4SiriusXM module
5SiriusXM antenna
Figure 1. Radio and SiriusXM Module
Figure 2. Correct SiriusXM Module Installation
Figure 3. Incorrect SiriusXM Module Installation
Antenna Mounting
Fork-Mounted Fairing
1. If equipped: Remove audio amplifier.
a. See Figure 4. Use a flat blade screwdriver to pull the latch down to release the connector.
b. See Figure 5. Disconnect amplifier [149].
c. Remove nuts (2) securing amplifier bracket (3) to mount (5).
d. Lift amplifier and pull studs (9) from grommets (8) to release.
Figure 4. Amplifier [149] Release Latch
1Amplifier
2Screw (2)
3Amplifier bracket
4Screw (2)
5Mount
6Screw (4)
7Pad (4)
8Grommet (2)
9Stud (2)
Figure 5. Amplifier and Mount - Typical
2. See Figure 6. If equipped: Disconnect right front tweeter/midrange [34T] (2).
3. If necessary: Disconnect P&A accessory power [299] (3).
4. Disconnect voltmeter [111] (5).
5. Disconnect harness retainer (4), and position harness out-of-way.
6. Remove front screw (6).
7. Loosen rear screw (7).
8. Install SiriusXM bracket (1).
9. Install front screw.
10. Tighten both front and rear screws.
Torque: 5.4–6.8 N·m (48–60 in-lbs)
11. Connect voltmeter [111].
12. If necessary: Connect P&A accessory power [299].
13. If equipped: Connect right front tweeter/midrange [34T].
14. Connect harness retainer.
15. If equipped: Install audio amplifier.
a. See Figure 5. Install studs into grommets (8).
b. Install nuts (2). Tighten.
Torque: 8.1–10.8 N·m (72–96 in-lbs)
c. Connect amplifier [149].
16. See Figure 8. Clean mounting surfaces of antenna (1) and bracket. Refer to Adhesive Strips.
17. Once dry, install adhesive pad (4) to bracket and install antenna onto adhesive pad.
18. Route antenna wire following existing harness routings.
19. See Figure 6. Connect SiriusXM antenna (5) to SiriusXM module (4).
20. See Figure 8. Install cable straps (3) to secure antenna cable to existing harnesses.
1SiriusXM bracket
2Right front tweeter/midrange [34T]
3P&A accessory power [299]
4Harness retainer
5Voltmeter [111]
6Front screw
7Rear screw
8Left front speaker enclosure
9Front amplifier mount (If equipped)
Figure 6. SiriusXM Bracket - Upper Right Inner Fairing
Frame Mounted Fairing
1. See Figure 7. Clean mounting surfaces of antenna. Refer to Adhesive Strips.
2. See Figure 8. Once dry, install adhesive pad (4) to bracket and install antenna onto adhesive pad.
3. Route antenna wire following existing harness routings.
4. See Figure 1. Connect SiriusXM antenna (5) to SiriusXM module (4).
5. Install cable straps (3) to secure antenna cable to existing harnesses.
Figure 7. SiriusXM Module Placement - Upper Left Inner Fairing
Adhesive Strips
1.
NOTE
  • Ambient temperature between 21–38 °C (70–100 °F) for proper adhesion. Do not apply below 10 °C (50.0 °F).
  • Parts cannot be repositioned after initial adhesive installation.
  • Allow at least 24 hours after application before exposing the area to vigorous washing, strong water spray or extreme weather.
  • The adhesive bond will increase to maximum strength after about 72 hours at normal room temperature.
  • Do not clean with denatured alcohol, mineral spirits or other solvents. Damage to components occurs.
Using a 50:50 isopropyl alcohol/water solution, thoroughly clean surface. Allow to dry completely.
2. Install item into area.
a. With the adhesive backing still in place, test fit the item to the area.
COMPLETE
1. Install main fuse. See the service manual.
2.
NOTE
The radio takes longer to boot up the first time while the radio updates menus and performs other functions.
Turn radio on to verify function. SiriusXM should now be a menu selection. Manually search for channel 1 prior to activation.
3. Install outer fairing. See the service manual.
4. Refer to the Boom! Box owner's manual for activation instructions. https://serviceinfo.harley-davidson.com
SERVICE PARTS
Figure 8. Service Parts: SiriusXM Module
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
SiriusXM antenna
76000221B
2
SiriusXM module
76000818
3
Cable strap (3)
10181
4
Adhesive pad
76498-06
5
Alcohol wipe
94678-00Y
6
SiriusXM bracket
76000809
Additional item mentioned in text:
A
Pin guard