COOLFLOW™ FAN KIT
J066622019-06-05
GENERAL
Kit Number
26800152
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation. One is available from a Harley-Davidson Dealer.
Kit Contents
See Figure 7 and Refer to Table 1.
PREPARE
WARNINGWhen installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
NOTE
Running amperage should be 2 A.
| 1. | Remove main fuse. See service manual | |
| 2. | Remove seat. See service manual. | |
| 3. | Remove components. See service manual. a. 2009-2013 models: Right saddlebag and side cover. b. 2014-2016 models: Left and right saddlebags and side covers. c. ALL Trike Models: Side covers. d. FLRT models: Fuel tank and wire troth cover. | |
| 4. | See Figure 1. Remove right side mid-frame deflector (1), if equipped. See the service manual. a. Remove self clinching nut (3) from frame. NOTE Use a drill or hammer and punch. |
INSTALLATION
With Mid-Frame Deflector (if equipped)
| 1. | See Figure 1. Install two spacers (4, 5) on inboard stud of fan assembly (6). | |
| 2. | Install one spacer (4) on outboard stud of fan assembly (6). | |
| 3. | Position bottom of mid-frame deflector onto outboard stud of fan assembly (6). | |
| 4. | Install fan assembly to frame. | |
| 5. | From within the battery tray area, install washers and nuts (2). Tighten. Torque: 6.8–8.1 N·m (5–6 ft-lbs) | |
| 6. | Install hardware to secure top of deflector to frame. See service manual. |
Without Mid-Frame Deflector
| 1. | See Figure 1. Install one spacer (4) on each stud of fan assembly (6). | |||||||||||||||||
| 2. | Install fan assembly to frame. | |||||||||||||||||
| 3. | From within the battery tray area, install washers and nuts (2). Tighten. Torque: 6.8–8.1 N·m (5–6 ft-lbs) | 
Figure 1. Assemble Fan to Frame |
Switch
| 1. | See Figure 7 and Refer to Table 1. Install fan switch. a. 2014-2016 Fairing models: Install switch panel (4) and accessory switch (8). See service manual. NOTE Install the switch panel (4) in the left side of dash panel. The accessory switch (8) should be installed in the far right slot of the switch panel. Add switch blanks (9) as needed. b. 2009-2013 Fairing models: Rocker switch is already installed from factory. c. 2009-2016 Road King: Toggle switch is already installed from factory. d. FLRT models: Require separate purchase of fan switch (715522-08), fan label (14001100) and nut (74408-08A). | |||||||
| 2. | 2015-1016 FLRT models: a. Locate 4-way connector [67A] inside wire troth near right side of steer head wire exit. b. Remove cap plug from right side of nacelle. Discard. c. Install fan switch (8) from back. d. Install fan label plate (9). e. Secure with nut (10). f. Mate fan switch connector to vehicle connector [67A] of main harness. g. Make sure harness is secured sufficiently in order to avoid any limitations in dynamic movement. | 
Figure 2. Non-Fairing Switch Location |
Harness 2009-2013 Models
| 1. | See Figure 3. Locate Parts and Accessory connector [4A] 4-place Deutsch (1) (Black) under seat. | |||
| 2. | Route connector from CoolFlow fan and connect to connector (1) under seat. | |||
| 3. | Secure harnesses with cable straps provided. | 
Figure 3. 2009-2013 Parts and Accessory Connector Location |
Harness 2014-2016 Models
| 1. | See Figure 4. Locate Parts and Accessory connector [4A] 8-way Molex (1) (Gray) under left side cover. | |||||||||||||||
| 2. | See Figure 5 and Figure 6. Connect vehicle P&A connector (1) to fan relay harness connector (2). | |||||||||||||||
| 3. | NOTE Do Not route harness over the vehicle frame. | |||||||||||||||
| 4. | Connect CoolFlow fan connector to fan relay harness connector (4). | |||||||||||||||
| 5. | Secure harnesses with cable straps provided. | 
Figure 4. 2014-2016 Parts and Accessory Connector Location 
Figure 5. 2014-2016 Road King and 2015-2016 FLRT Models 
Figure 6. 2014-2016 Models EXCEPT Road King |
COMPLETE
| 1. | Install side cover and saddlebag. See service manual. | |
| 2. | FLRT models: Install wire troth and fuel tank. See service manual. | |
| 3. | Install seat. After installing seat, pull up on the seat to verify that it is secure. See service manual. | |
| 4. | Install main fuse. See service manual. | |
| 5. | Perform operations check on fan switch. |
OPERATION
NOTE
Verify that fan is turned OFF before starting the engine.
Operating the fan after reaching 40 mph will not increase comfort level for the rider or passenger.
The CoolFlow fan is a manual switch operation. Either ON/OFF.
- Recommended ON setting: Manually turn on at speeds below 64 km/h (40 mph)
- Recommended OFF setting: Manually turn off at speeds above 64 km/h (40 mph)
SERVICE PARTS
Figure 7.
Table 1. Service Parts Table
Item | Description (QTY) | Part Number |
|---|---|---|
1 | Wire Harness, Chassis Fan (2014-2016 non-fairing) | 69201906 |
2 | Wire Harness, Dash Panel (accessory) (2014-2016 with fairing) | 69200926 |
3 | Fan assembly | 26800151 |
4 | Dash panel base | 69200173 |
5 | Spacer (3) | 26800172 |
6 | Washer (2) | 6235 |
7 | Lock nut (2) | 7686 |
8 | Switch, accessory (2) | 71400109 |
9 | Switch, dash panel, blank | 71400031 |
10 | Cable strap (4) | 10006 |
Items mentioned in text but not included in kit: | ||
A | Nut | 74408-08A |
B | Label, fan switch | 14001100 |
C | Switch, fan, momentary | 71522-08 |