BOOM! AUDIO EXPAND BLUETOOTH HEADSET
J066792020-08-21
GENERAL
Kit Number
76000835
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
The internal lithium battery is NOT replaceable. Consumers are responsible for recycling used electronics. Dispose in accordance with methods that meet or exceed all state and federal environmental laws. INSTALLATION REQUIREMENTS
Visit https://serviceinfo.harley-davidson.com for the latest instruction sheet.
Pair with Phone
For greater detail in pairing a bluetooth device or additional information pertaining to the wireless headset, see the Sena User’s Guide .
WIRELESS HEADSET
Read the User’s Guide for additional information pertaining to the wireless headset. Also see Harley-Davidson.com for the latest version of User's Guide and related information to Boom! Audio Bluetooth products or visit your local Harley-Davidson dealership.
Getting Started
See quick-start guide provided with this product for basic operation of the Bluetooth module.
Charge wireless headset by connecting the supplied USB power and data cable into a computer USB port or USB wall charger. Use any standard micro-USB cable to charge the headset. The LED turns red while the headset is charging and turns blue when it is fully charged. It takes about 2.5 hours to charge completely.
Headset Software Version
The HELMET WITH INTEGRATED BOOM! AUDIO BLUETOOTH HEADSET supports firmware upgrade function. Visit www.H-D.com/infotainment-support to check for the latest software downloads.
Powering On and Off
- Powering On: Press and hold the Center Button and the (+) Button at the same time for 1 second to power on. The blue status LED turns on and you will hear ascending beeps and Hello.
- Powering Off: Press the Center Button and the (+) Button simultaneously (you do not need to press and hold in order for the system to power off). The red status LED turns on for about 2 seconds until it turns off completely and you will hear Goodbye and descending beeps.
| 1 | Microphone |
| 2 | Center button |
| 3 | (+) Button |
| 4 | Status LED |
| 5 | Charging and firmware port |
| 6 | Charging LED |
| 7 | (-) Button |
Figure 1. EXPAND Headset
WIRELESS HEADSET SETUP
Before using the wireless headset with any Bluetooth devices for the first time, you will need to pair them together. For example, it can be paired with Bluetooth mobile phones, Bluetooth stereo devices such as MP3 players, or motorcycle-specific Bluetooth GPS navigation, and with other Boom! Audio Bluetooth headsets. This pairing operation is only required once for any Bluetooth device. The headset remains paired with the devices and automatically reconnects to them when they are within range. You will hear a high tone single beep and a voice prompt when the headset connects to the paired device automatically:
When a headset is paired to a phone, it will confirm the pairing by saying Your Headset is Paired. After this initial pairing, every time the headset reconnects to the phone it will say Phone Connected.
Headset-to-Headset Intercom Pairing
NOTE
When in pairing mode, do one device at a time in the area of the motorcycle and headset.
Read the User’s Guide for information pertaining to the wireless headset to headset intercom setup and usage.
Reset Factory Headset Settings
NOTE
When performing this procedure, the link between the bluetooth device and headset will be broken. The wireless headsets must be paired again for system communications to operate properly.
To restore factory default settings on the EXPAND, press the (+) Button or the (-) Button until you hear the voice prompt, Factory reset. Press the Center Button to confirm. The EXPAND powers off with a voice prompt, Headset reset, goodbye.
You can also restore factory default settings on EXPAND by pressing the Center Button and the (+) Button for 12 seconds and tap Center Button to confirm.
Fault Reset
When the EXPAND is not working properly or is faulty for any reason, you may reset it by pushing the pinhole reset button at the back of the headset main unit.
| 1. | See Figure 2. Rotate the speaker pad (1) of the left headset counterclockwise to detach it. | |
| 2. | Insert a paper clip into the reset pin-hole and press the reset button (2) for a second using light pressure. The EXPAND will be switched off, and have to turn the system back on and try again. However, this will not restore the headset to the factory default settings. |
| 1 | Speaker pad |
| 2 | Reset button |
Figure 2. Fault Reset
SERVICE PARTS
Figure 3. Expand Ear Pads
Table 1. Service Parts
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | USB and data cable | GEP0601079 |
2 | Microphone windscreen | GSA0105024 |
3 | Ear pads (2) | GSA0104154 |