PASSENGER FOOTPEG
J067742021-08-02
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
50501643, 50501644, 50502026 | Safety Glasses, E-Clip Tool |  |
(1) Only simple tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Passenger Footpeg Components
Table 2. Kit Contents: Passenger Footpeg Components
 | Item | Qty | Description | Part No. | Notes |
|---|---|---|---|---|---|
 | 1 | 1 | Footpeg, passenger, right side, graphite | 50501706 | |
| 1 | Footpeg, passenger, right side, black | 50501707 | ||
| 1 | Footpeg, passenger, right side, black | 50502024 | ||
| 2 | 2 | Plate, passenger footpeg, graphite | 50502039 | |
| 3 | 1 | Footpeg, passenger, left side, graphite | 50501708 | |
| 1 | Footpeg, passenger, left side, black | 50501709 | ||
| 1 | Footpeg, passenger, left side, black | 50502025 |
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit.
If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation.
Improper installation of this kit could result in death or serious injury. (00308b)
REMOVE
| 1. | Softail models: See Figure 2. Remove clevis pin (2) and E-clip (1). Retain for later use. | |
| 2. | Models equipped with Revolution Max engines: See Figure 3. Depress spring loaded detent and remove clevis pin (1). | |
| 3. | Remove detent plate (5). a. Softail models: Discard detent plate. b. Models equipped with Revolution Max engines: Retain detent plate. | |
| 4. | Save all hardware including detent spring (7) and detent ball (6) for installation of new footpegs (3). |
INSTALL
| 1. | See Figure 2. Insert detent spring (7) into new footpeg (3). NOTE When performing the next step, verify that the detent spring (7) is positioned inside of the footpeg (3). | |
| 2. | Insert detent ball (6). | |
| 3. | Install detent. a. Softail models: Position new detent plate (5) on footpeg clevis edge while capturing detent ball (6) and detent spring (7) inside detent plate (5) while sliding detent plate (5) onto footpeg clevis. b. Models equipped with Revolution Max engines: Position retained detent plate (5) on footpeg clevis edge while capturing detent ball (6) and detent spring (7) inside detent plate (5) while sliding detent plate (5) onto footpeg clevis. | |
| 4. | Align detent plate (5) and footpeg (3) with footpeg support on vehicle. | |
| 5. | Softail models: Install clevis pin (2) and E-clip (1). Special Tool: E-CLIP TOOL (HD-52369) | |
| 6. | Models equipped with Revolution Max engines: See Figure 3. Install clevis pin (1). |
| 1 | E-clip |
| 2 | Clevis pin |
| 3 | Passenger footpeg |
| 4 | Support, footpeg |
| 5 | Detent plate |
| 6 | Detent ball |
| 7 | Detent spring |
Figure 2. Remove/Install Footpeg Assembly
| 1 | Clevis pin |
| 2 | Footpeg, passenger |
| 3 | Decorative screws |
Figure 3. Kit 50502026: Install Footpeg Assembly w/ Spring Loaded Detent
NOTE
See Figure 3. Screws on centerline of footpegs are for decorative purpose only. Do not tighten.