RIDER FOOTBOARD - TOURING
J067752024-05-07
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
50501649, 50501680, 50501932, 50501933, 50501934, 50502250, 50502251, 50502476, 50502483 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Rider Footboard Components
Table 2. Kit Contents: Rider Footboard Components
 | Item | Qty | Description | Part No. | Notes |
|---|---|---|---|---|---|
 | 1 | 4 | Screw | 10200986 | Not used on Switchback footboard. |
| 2 | 4 | Locking nut, flange | 7716 | Not used on Switchback footboard. |
| 3 | 1 | Footboard assembly, right side, graphite | 50502093 | Endgame Collection |
| 1 | Footboard assembly, right side, black | 50502094 | Endgame Collection | |
| 1 | Footboard assembly, right side, chrome | 50501926 | Empire Collection | |
| 1 | Footboard assembly, right side, black | 50501928 | Empire Collection | |
| 1 | Footboard assembly, right side, machine cut | 50501930 | Empire Collection | |
| 1 | Footboard assembly, right side, gray | 50502323 | Adversary Collection | |
| 1 | Footboard assembly, right side, black | 50502322 | Adversary Collection | |
| 1 | Footboard assembly, right side, black | 50502477 | Switchback Collection | |
| 1 | Footboard assembly, right side, silver | 50502484 | Switchback Collection | |
| 4 | 1 | Footboard assembly, left side, graphite | 50502095 | Endgame Collection |
| 1 | Footboard assembly, left side, black | 50502096 | Endgame Collection | |
| 1 | Footboard assembly, left side, chrome | 50501927 | Empire Collection | |
| 1 | Footboard assembly, left side, black | 50501929 | Empire Collection | |
| 1 | Footboard assembly, left side, machine cut | 50501931 | Empire Collection | |
| 1 | Footboard assembly, left side, gray | 50502325 | Adversary Collection | |
| 1 | Footboard assembly, left side, black | 50502324 | Adversary Collection | |
| 1 | Footboard assembly, left side, black | 50502477 | Switchback Collection | |
| 1 | Footboard assembly, left side, silver | 50502484 | Switchback Collection | |
| 5 | 2 | Wear peg | 50501135 | Endgame Collection |
| 2 | Wear peg | 50500628 | Empire and Adversary Collections | |
| 6 | 2 | Wear plate (not shown) | 50502575 | Switchback Collection |
| 7 | 2 | Screw, wear plate (not shown) | 10200659 | Switchback Collection |
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
FLTRXSTSE Models: Separate purchase of Front Support Mounts (Part No. 47200302A (Qty 2) is required. See service manual for removal of old front supports and install of new supports.
WARNINGRider and passenger safety depend upon the correct installation of this kit.
If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation.
Improper installation of this kit could result in death or serious injury. (00308b)
REMOVE
| 1. | Remove two hinge bolts and locknuts attaching existing footboard to mounting brackets. | |
| 2. | Remove footboard. | |
| 3. | Vehicle hardware: a. Switchback footboards: Save hardware. b. All other footboards: Discard hardware. |
INSTALL
| 1. | See Figure 1. Set correct footboard in place over mounting brackets. Wear peg should be toward rear of vehicle. | |
| 2. | Align holes, install pivot screws (1) and locking nuts (2). a. Switchback footboards: Use saved hardware. | |
| 3. | Locking nuts should be on inboard side. Tighten. Torque: 9–12 N·m (80–106 in-lbs) | |
| 4. | Check that footboard pivots freely on hinge bolts. | |
| 5. | Repeat for opposite side. |
Wear Peg Replacement
| 1. | When servicing wear peg, remove existing wear peg from footpeg. | |
| 2. | Apply two or three drops of threadlocker to threads of new wear peg.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) | |
| 3. | Install new wear peg to footpeg. Torque: 3.38–4.74 N·m (30–42 in-lbs) |
Wear Plate Replacement
| 1. | When servicing wear plate, remove existing wear plate screws. | |
| 2. | Apply two or three drops of threadlocker to threads of screws.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) | |
| 3. | Install new wear plate and screws. Torque: 2.03 N·m (18 in-lbs) |