BOARD-TO-PEG CONVERSION KIT
J067772020-01-14
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) | Time |
|---|---|---|---|
50501642 | Safety Glasses, Torque Wrench, E-clip Tool |  | 1 hour |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Board-to-Peg Conversion Kit Components
Table 2. Kit Contents: Board-to-Peg Conversion Kit Components
 | Item | Qty | Description | Part No. | Notes |
|---|---|---|---|---|---|
 | 1 | 2 | Clevis Pin | 50500702 | |
| 2 | 2 | Spring | 50500703 | |
| 3 | 2 | E-clip | 50500701 | |
| 4 | 1 | Screw, black | 4688 | |
| 5 | 3 | Screw | 10200429 | |
| 6 | 3 | Lockwasher | 7038 | |
| 7 | 1 | Bracket, right side footpeg mount, black | 50501698 | |
| 8 | 1 | Bracket, left side footpeg mount, black | 50501701 |
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
REMOVE
| 1. | Remove right and left side footboard and mounting brackets. See service manual. |
INSTALL
RIGHT SIDE
| 1. | See Figure 2. Position right side forward control bracket (1). | |
| 2. | Install front screw (3) and lockwasher (2). Tighten. Torque: 48.8–56.9 N·m (36–42 ft-lbs) | |
| 3. | Install rear screw (4). Tighten. Torque: 48.8–56.9 N·m (36–42 ft-lbs) | |
| 4. | See Figure 4. Insert short leg of spring (1) into hole in footpeg (3). NOTE See Figure 3. When performing the next step, verify that the spring is positioned inside of the footpeg. | |
| 5. | Align long leg of spring (1) to hole in footpeg mount and insert. | |
| 6. | Rotate footpeg (3) into position in clevis and insert pin (4) through clevis, footpeg (3) and spring (1). | |
| 7. | Install E-clip (2). |
| 1 | Right side forward control bracket |
| 2 | Lockwasher |
| 3 | Screw |
| 4 | Screw |
Figure 2. Right Side Forward Control
Figure 3. Torsion Spring
| 1 | Spring |
| 2 | E-clip |
| 3 | Footpeg assembly |
| 4 | Clevis pin |
Figure 4. Rider Footpeg Torsion Spring Installation
LEFT SIDE
| 1. | See Figure 5. Position left side forward control bracket (2). | |
| 2. | Install screws (4) and lockerwashers (3). Tighten. Torque: 48.8–56.9 N·m (36–42 ft-lbs) | |
| 3. | Insert short leg of spring (5) into hole in footpeg (2). NOTE When performing the next step, verify that the spring is positioned inside of the footpeg. | |
| 4. | Align long leg of spring (5) to hole in footpeg mount and insert. | |
| 5. | Rotate footpeg into position in clevis and insert pin (1) through clevis, footpeg and spring (5). | |
| 6. | Install E-clip (6). |
| 1 | Clevis pin |
| 2 | Bracket, left side footpeg mount |
| 3 | Lockwashers |
| 4 | Screws |
| 5 | Spring |
| 6 | E-clip |
Figure 5. Left Side Forward Control