0/0
FAIRING LOWER SPEAKER INSTALLATION KIT FOR BOOM! AUDIO
941000622019-01-31
GENERAL
The Boom!™ Audio system speakers in this kit work with either Stage I or Stage II systems.
These speakers are designed to fit in the lower fairings of Twin-Cooled™ models.
Kit Number
76000734, 76000957
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
FLHXSE models require template and cover kit (Part No. 76000734).
Prior or Simultaneous installation of Stage I or Stage II Fairing Amplifier kit.
FLTRUSE and FLHTCUTG models require jumper (Part No. 69200489) and interconnect (Part No. 69200714).
Vehicles with Stage I a speaker expansion kit is required to enable six or eight speakers.
Vehicles with Stage II purchase of Lower Amplifier Kit (Part No. 76000277A). Lower Speaker Installation Kit (Part No. 76000586).
2015 and newer FLXSE must use the template in this kit for amplifier installation.
NOTICE
Radio EQ MUST be updated by a Harley-Davidson dealer BEFORE operating the audio system. Operating the audio system prior to radio EQ update will IMMEDIATELY damage the speakers. (00645d)
Radio EQ update using the Digital Technician® II diagnostic tool is:
  • Recommended before speaker INSTALLATION
  • Required before audio system OPERATION.
  • Only available through authorized Harley-Davidson dealers.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Electrical Overload
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
WARNING
When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
The amplifier installed with this kit requires up to 8 amps more current from the electrical system.
Kit Contents
See Figure 4 and Table 1.
PREPARATION
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
  1. See the service manual. Remove fuse.
  2. All Models: If simultaneous installation of Stage I or Stage II amplifier/speaker set, complete the fairing installation now.
  3. Remove and discard both fairing lower access doors.
  4. Remove outer fairing. See the service manual.
  5. Stage I: Install speaker expansion kit.
  6. Stage II: Remove right side saddlebag. Remove seat. Remove side covers. See the service manual.
SPEAKER INSTALLATION
  1. See Figure 4. Stage I: Route the small terminal leads on wire harness (10) to the lower fairing. Stage II: Wire harness (10) is not used. Discard wire harness. Route the vehicle side harness per the instructions in the amplifier installation kit. DO NOT drill any holes in faring lower.
  2. Route the harness along the main harness to the right side of the steering head.
  3. Route the harness through the fairing. Verify that there is no interference with steering. Allow about 14 in of wire inside the fairing lower compartment.
  4. Locate the speakers. Locate the tweeter on the outboard side when installed.
  5. See Figure 1. Route wire through small opening (2). Keep wire from contacting the vent (4) and vent control (3).
  6. Repeat on other side.
  7. Install the wire harness leads to the cross-over board on the back of the speakers. Leave enough slack to enable speaker removal to access the coolant bottle.
  8. Repeat on other side.
  9. Secure wires with cable strap (5).
  10. Snap speakers into place.
1Speaker wire
2Opening in lower fairing
3Vent control
4Vent
5Cable strap
Figure 1. Speaker Wire Routing
AMPLIFIER INSTALLATION
Stage I:
All Models Except CVO Ultra and Trike: Locate connector [313] rear speaker output of primary amplifier.
Connect [313] to wire harness (10). See Figure 4. Proceed to COMPLETION Section.
CVO Ultra and Trike: Insert 6920714 (unless already in place) into connector [162] behind passenger seat.
Connect socket side 4-way to speaker expansion harness audio [297] and 4-way pin side to socket side of 69200489 jumper. Connect pin side of 69200489 jumper to wire harness from this kit (10).
Unless previously installed, connect vehicle connector [296] (4-way pin side Molex under seat) to 296 (4-way socket side) of speaker expansion kit.
Stage II:
NOTE
All models: Two-way tweeter connector [36RT and 37LT] is NOT used for stage II applications. Cover the connector ends with tape, stow and secure with cable straps.
All models except 2015 and later FLHXSE: Proceed to the COMPLETION section of this document.
2015 and later FLHXSE: follow instructions in this kit and the instructions in installation kit Part No. 76000734.
2015 FLHXSE:
Discard the template included in the Stage II Fairing Lower Speaker kit. Use the template included in this kit. See Figure 2.
  1. See Figure 3. Use the template (1) to cut the openings in the saddlebag for the fairing lower amplifier 18-way flanged connector [289-1].
    1. Saddlebag lid speakers are present from a stock installation, right side speaker wires could be in the connector cutout location. Remove stock wire harness and 4-way connector.
    2. Place the template on the saddlebag. Align the grommet (2) and latch fastener (3) openings. Use tape (10) to secure the template in place.
    3. Place masking tape on the opposite side of the template to reduce possible paint damage to the outside of the saddlebag.
    4. Trace the cut outline (4) onto the saddlebag. Trace the cut outline (7) onto the saddlebag. Trace the cut outline (9) onto the saddlebag.
    5. Drill two 9/32 in holes (5) for the connector flange mounting locations. Drill five 3/16 in holes (6) for the connector flange mounting locations. Drill five 3/16 in holes (8) for the connector flange mounting locations.
    6. Remove template. Use an air saw or similar tool to cutout the connector cutout (4). Verify size of opening (4) with the 18-way flanged connector [289-1A] on the saddlebag harness (see Figure 4 , Item 7). Shape the hole as seen on the template if necessary for proper fit.
2016 and later FLHXSE:
Discard the template included in the Stage II Fairing Lower Speaker kit. Use the template included in this kit. See Figure 2.
  1. See Figure 3. Use the template (1) to cut the openings in the saddlebag for the fairing lower amplifier 18-way flanged connector [289-1].
    1. Cut the bottom of the template along cut line (11). Discard the bottom of the template.
    2. Saddlebag lid speakers are present from stock installation, this connector remains as is.
    3. Place the template on the saddlebag. Align the grommet (2) and latch fastener (3) openings. Use tape (10) to secure the template in place.
    4. Place masking tape on the opposite side of the template to reduce possible paint damage to the outside of the saddlebag.
    5. Trace the cut outline (4) onto the saddlebag. Trace the cut outline (7) onto the saddlebag.
    6. Drill two 9/32 in holes (5) for the connector flange mounting locations. Drill five 3/16 in holes (6) for the connector flange mounting locations.
    7. Remove template. Use an air saw or similar tool to cutout the connector cutout (4). Verify size of opening (4) with the 18-way flanged connector [289-1A] on the saddlebag harness (see Figure 4 , Item 7). Shape the hole as seen on the template if necessary for proper fit.
    8. After installing the 18-way connector [289-1]: Install connector cover (12) over it by snapping in place. Secure wire bundles inside bag using cable straps and adhesive bases provided with amplifier installation kit. Complete Stage II amplifier installation per instruction in that kit.
Cut openings for four-way connector [289-2]:
See Figure 3 , Items 6 and 7.
  1. Use the outlines made earlier and the center pilot hole to drill a hole for the upper four-way flanged connector [289-2].
    1. Use a step drill to make a 7/8 in hole for connector cutout (7).
    2. Use a file to make the flats at the top of the hole.
    3. Test-fit the connector [289-2]. Shape the hole as seen on the template if necessary for proper fit.
1Template
2Cut line 2016 and later FLHXSE
Figure 2. 2015 and Later FLHXSE (CVO Street Glide)
1Template
2Saddlebag rear grommet
3Saddlebag rear latch fastener (4)
4Cutout, connector
5Flange mounting hole (2)
6Flange mounting hole (4)
7Cutout, connector
8Flange mounting hole (4) (2015 FLXSE only)
9Cutout, connector (2015 FLXSE only)
10Tape
11Cut line
Figure 3. Right Saddlebag Cutout and Drilling Harness Installation
COMPLETION
NOTE
To prevent possible damage to the sound system, verify that the ignition switch is OFF before attaching the battery cables.
WARNING
Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a)
  1. Apply a light coat of petroleum jelly or corrosion retardant material to battery terminals.
  2. Install the ECM caddy per the service manual.
  3. See the service manual. Install seat. After installing seat, pull up on the seat to verify that it is secure.
  4. Install main fuse.
  5. Have a Harley-Davidson dealer update the radio EQ using Digital Technician II.
SERVICE PARTS
Figure 4. Service Parts, Fairing Lower Speakers
Table 1. Service Parts
Kit
Item
Description (Quantity)
Part Number
Kit 76000957
1
Screw, # 8 x 1/2 in (8)
10201030
2
Grille Assembly, left side
76000968
3
Grille Assembly, right side (not shown)
76000967
4
Speaker, lower, stage 1 or 2 (2)
76000966
5
Speaker mount (2)
76000969
6
Panel clip (6)
12200025
7
Speaker assembly, left side
Not Sold Separately
8
Speaker assembly, right side
Not Sold Separately
9
Cable strap (6)
10006
10
Wire harness
69200612
Kit 76000734
11
Template, drill, cutout
76000733
12
Connector cover
69201566