SOFT SADDLEBAGS

941001152021-06-22

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
90202107	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Soft Saddlebags

Table 2. Kit Contents: Soft Saddlebags

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	2	Support bracket, saddlebag	67900650
2	4	Screw, button head, M6	10201320
3	2	Reflector, red	67900205A
4	2	Soft saddlebag	90202251	Not shown

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)

These items are available at your local Harley-Davidson dealership.

Separate purchase of Side Case Mounting Kit (Part No. 90202087) is required for this installation.

PREPARE

NOTE

See Figure 2. Latch plate nuts (3) (Part No. 10100152) are from the Side Case Mounting Kit.

Remove any mounting spools, latch plates and hardware used for mounting aluminum luggage.

a. Save latch plate nuts for later use.

INSTALL

See Figure 2. Install saddlebag support bracket (1) to saddlebag support frame.

Install screws (2) and latch plate nuts (3). Tightened screws.

Torque: 9.5 N·m (7 ft-lbs) Support bracket screw

Repeat procedure for opposite side.

1	Saddlebag support bracket
2	M6 Screw (2)
3	Latch plate nuts

Figure 2. Mount Brackets

See Figure 3. Install saddlebags on vehicle with straps connected over rear seat pillion.

See Figure 4. Align reflective stripe (2) on saddlebag with lower horizontal support (3). Adjust straps as needed.

NOTE

Proper bag height should be maintained to reduce likelihood of saddlebag contacting the ground while cornering at maximum lean angle.

See Figure 3. Place excess straps into elastic loops (1).

See Figure 5. Wrap saddlebag tension straps (3) around saddlebag support frame (4).

a. Four tension straps per saddlebag.

Tighten saddlebag to support frame.

a. See Figure 6 and Figure 7. Insert small buckle (1) into large buckle (2).

b. Tighten tension straps as needed.

See Figure 8. Tension straps (2, 3, 4) should be attached in approximate locations.

10.

Secure any loose strap length with elastic loops.

1	Elastic loop
2	Assembled buckles

Figure 3. Straps Across Pillion

1	Saddlebag
2	Reflective stripe
3	Lower horizontal support

Figure 4. Install Saddlebag

1	Small buckle
2	Large buckle
3	Strap
4	Support frame

Figure 5. Tension Strap Process 1

1	Small buckle
2	Large buckle

Figure 6. Tension Strap Process 2

1	Small buckle
2	Large buckle

Figure 7. Tension Strap Process 3

1	Support frame
2	Upper tension strap
3	Lower tension strap
4	Vertical tension strap

Figure 8. Tension All Straps