SHIFT SIDE MID-CONTROL

941001232021-04-01

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾	Time
50502090	Safety Glasses, Torque Wrench, E-CLIP TOOL (Part Number:HD-52369), LOCTITE 243 (BLUE) (99642-97)		1 hour

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Shift Side Mid-Control

Table 2. Kit Contents: Shift Side Mid-Control

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Foot shift lever	33600233
2	2	Screw	4387
3	1	Screw, pinch	856A
4	1	Spacer	7078
5	1	Shifter rod	33600125
6	1	Front shifter rod lever	33600143
7	1	Lever shaft	33900199A
8	1	Screw	2932A
9	1	Washer	6702
10	1	Nut	7748W
11	1	Foot support bracket	50500603
12	2	Screw, foot support bracket	10200536
13	1	Plug	10040
14	1	Shifter peg	33600156
15	1	Screw	34591-08

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

These part are available at a Harley Davidson dealership:

Separate purchase of Outer Primary Cover (25700937) or (25700941).
Separate purchase of Inner Primary Cover (36500105).
Separate purchase of Gasket Kit (25701079).
Separate purchase of Gasket (63869-06).
Separate purchase of Bushing (34982-02A).

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealership.
H-D Service Information Portal, a subscription-based access is available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

PREPARE

Set vehicle upright. See service manual.

REMOVE

1.	See Figure 3. Remove footpeg. a. Remove E-clip (2) using special tool. Special Tool: E-CLIP TOOL (HD-52369) b. Remove clevis pin (5). c. Remove footpeg (3). d. Remove torsion spring (4).
2.	Disconnect shifter connecting rod from transmission gear shift lever.
3.	See Figure 2. Remove foot support bracket. a. Remove screws (2). b. Remove foot support bracket (1).
4.	Remove outer and inner primary covers. See service manual.

1	Foot support bracket
2	Screw (2)

Figure 2. Left Foot Support Bracket (Typical)

1	O-ring (2)
2	E-clip
3	Footpeg
4	Torsion spring
5	Clevis Pin
6	Foot support bracket
7	Wear Peg

Figure 3. Left Side Footpeg (Typical)

INSTALL

Front Shifter Rod Lever

1.	See Figure 4. Install front shifter rod lever (1) onto lever shaft (10).
2.	Install pinch screw (11). Tighten. Torque: 24.4–29.8 N·m (216–264 in-lbs) Front shifter rod lever pinch screw
3.	Install bushing (34982-02A) in new inner primary with hole. See service manual.
4.	Install front shifter rod lever (7) with shaft (10) through new inner primary cover.
5.	Install inner primary cover with new gasket. See service manual.
6.	Assemble primary drive components. See service manual.
7.	Install new outer primary cover with hole and new gaskets. See service manual.

Shifter Rod

See Figure 4. Install shifter rod.

a. Install shifter rod (3) to each shifter rod lever (1, 2).

b. Install screws (4). Tighten.

Torque: 13.6–19 N·m (120–168 in-lbs)

Foot Support Bracket

1.	See Figure 5. Install foot support bracket. a. Install foot support bracket (1). b. Install screws (2). Tighten. Torque: 54–61 N·m (40–45 ft-lbs)
2.	Install plug into empty hole in vehicle frame.
3.	NOTE When installing E-clip, use E-clip tool to help prevent damage to painted surfaces. See Figure 3. Install footpeg removed earlier. a. Insert short leg of torsion spring (4) into hole in footpeg (3). b. Insert long leg of torsion spring (4) into hole in foot support bracket (6). c. Rotate footpeg into position. d. Install clevis pin (5). e. Install E-clip (2). Special Tool: E-CLIP TOOL (HD-52369)

Foot Shift Lever

NOTE

Foot shift lever peg height is a customer preference. During installation, check operation of shift lever. To achieve proper gear engagement and to avoid damage to transmission, the peg must not contact foortboard or supports when shifting.

1.	See Figure 1. Install shifter peg (14) and screw (15) to foot shift lever (1). Tighten. Torque: 10.8–16.2 N·m (8–12 ft-lbs)
2.	See Figure 4. Install spacer (8) onto lever shaft (10).
3.	See Figure 4. Install foot shift lever. a. Install foot shift lever (7) onto lever shaft (10). b. Position shifter peg at preferred height. c. Install pinch screw (5), washer (6) and nut (9). d. Tighten. Torque: 32.5–38 N·m (24–28 ft-lbs) Foot shift lever pinch screw
4.	NOTE Shifter rod should not require adjustment under normal circumstances. However, if full gear engagement or full lever travel is not achieved, adjust shifter rod. Do not allow shift lever to contact support bracket when shifting. This prevents proper gear engagement. Contact may also damage the transmission. See Figure 4. Adjust shifter rod. a. Disconnect forward end of shifter rod from forward shifter rod lever. b. Loosen jamnuts. c. Adjust shifter rod (3) as necessary. d. Secure shifter rod (3) to front shifter rod lever (1). Tighten. Torque: 13.6–19 N·m (120–168 in-lbs) e. Tighten jamnuts. Torque: 9.5–14.9 N·m (84–132 in-lbs)

1	Shifter rod lever, front
2	Shifter rod lever, rear
3	Shifter rod
4	Screw (2)
5	Pinch screw
6	Washer
7	Foot shift lever
8	Spacer
9	Nut
10	Lever shaft
11	Pinch screw

Figure 4. Shift Linkage

1	Foot support bracket
2	Screw (2)

Figure 5. Mid Controls