AIR COOLED FAIRING LOWER SPEAKER HARNESS INSTALL KIT (PN 76000978)
941001542022-01-21
GENERAL
NOTE
The newly installed audio system and speakers will not play audio unless it is configured using the Harley-Davidson audio app or by an authorized Harley-Davidson dealership.
Table 1.
Harley-Davidson Audio Powered by Rockford Fosgate® | |
|---|---|
Kit | QR Code |
76000978 | N/A |
NOTE
The various generations of speakers, amplifiers and wiring for Harley-Davidson vehicles were not designed or tested to work together. Please consult your dealership to ensure optimal performance and compatibility.
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of http://www.harley-davidson.com (English only).
Ensure you are using the most current version of the instruction sheet which is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
Download Harley-Davidson audio app.
Use this kit in conjunction with other Harley-Davidson Audio powered by Rockford Fosgate® kits.
This harness is for use ONLY on 2014 and later Harley-Davidson audio systems.
- 2014 and Later Touring: Separate purchase of Harley-Davidson Color Matched Fairing Lowers Speaker Front Enclosure (Part No. 57100233) is required for this installation. ALL models require separate purchase of left and right speaker front enclosures. See your dealership or contact Harley-Davidson Customer Support Center for proper color match.
- 2014 and Later Touring: Separate purchase of Harley-Davidson Color Matched Vented Fairing Lower Kit (Part No. 57100258xxx) may be required for this installation. FLH or FLTR models require prior or concurrent installation of Harley-Davidson air-cooled fairing lowers.
- 2014 and Later Touring: Separate purchase of Harley-Davidson Primary Amplifier and Dongle Kit (Part No. 76000997) is required for this installation.
- 2014 and Later Touring: Separate purchase of Harley-Davidson Primary Amplifier Installation Kit (Part No. 76000974 or 76001045) is required for this installation.
- 2014 and Later Touring: Separate purchase of Harley-Davidson Secondary Amplifier Installation Kit (Part No. 76000975) may be required for this installation. This depends if there are six or more speakers and how the amplifier channels are assigned.
- 2014 and Later Touring: Separate purchase of Harley-Davidson Stage 1 or 2 Speaker Kit (Part No. 76000984 or 76000985) may be required for this installation.
These items are available at your Harley-Davidson dealership.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
Installation by a technician at a Harley-Davidson dealership is recommended.
PREPARE
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
| 1. | Remove left and right saddlebags. | |
| 2. | Remove left and right side covers. | |
| 3. | Remove main fuse. NOTE Models with security: Disable security system. | |
| 4. | Remove seat. | |
| 5. | Remove fuel tank. | |
| 6. | Remove wire trough cover. |
VENTED FAIRING LOWER
NOTE
See Installation Requirements for proper components that are needed for the assembly.
| 1. | Remove lower fairings. | |||||||||||
| 2. | See Figure 1. From the back: Remove screws (1). | 
Figure 1. Rear Screws | ||||||||||
| 3. | See Figure 2. From the front: Remove screws (3), block-off panel (4) and glove box (2). a. Disconnect vent door linkage. | 
Figure 2. Locking Tab and Block-off Panel | ||||||||||
| 4. | See Figure 3. Remove glove box screws (1) and glove box (2). | 
Figure 3. Glove Box Screws | ||||||||||
| 5. | See Figure 19. Remove screw (1) and linkage (2). a. Install components on new front enclosure. Tighten. Torque: 1.3–2 N·m (12–18 in-lbs) | 
Figure 4. Vent Linkage Screw | ||||||||||
| 6. | See Figure 5. Clean the gasket contact surface area (1) with a mixture of 50-70 percent isopropyl alcohol and 30-50 percent distilled water. | 
Figure 5. Gasket Mating Surface of Lower Fairing | ||||||||||
| 7. | See Figure 6. Assemble front enclosure (2) and enclosure tray (3). a. Clean the edge of the tray flange where the foam gasket (4) is to adhere with a mixture of 50-70 percent isopropyl alcohol and 30-50 percent distilled water. b. Start at one end and wrap gasket around the enclosure tray (3). c. Trim and save excess gasket. d. Insert enclosure tray (3) to the front locating ribs (1). | 
Figure 6. Enclosure Assembly | ||||||||||
| 8. | See Figure 7. Position the enclosure assembly and connect the linkage (1). | 
Figure 7. Connect Linkage | ||||||||||
| 9. | See Figure 8. From the rear: Install enclosure screws (1). Tighten. Torque: 1.3–2 N·m (12–18 in-lbs) |
Figure 8. Rear Screws | ||||||||||
| 10. | See Figure 9. Fold a piece of trimmed gasket (1)over the locating tab of the block-off panel and install the panel. a. Apply threadlocker to the threads of the screws (4).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) b. Install screws (4). Tighten. Torque: 7.3–8.4 N·m (65–74 in-lbs) | 
Figure 9. Block-off Panel and Locating Tab Foam | ||||||||||
| 11. | See Figure 10. Drill hole in back of lower fairing. a. From outer side edge (A), mark a parallel line (B) at the specified distance (C). Length/Dimension/Distance: 25 mm (1.0 in) b. From the bottom edge (D) mark a spot on the parallel line at the specified distance (E). Length/Dimension/Distance: 9.5 mm (0.374 in) | 
Figure 10. Drill Location | ||||||||||
| 12. | Cover drill point with masking tape to prevent cracking or chipping of paint. | |||||||||||
| 13. | At the drill location on the glove box inboard side wall, drill a hole. Diameter: 25 mm (1 in) a. De-burr holes by lightly sanding the surface. | |||||||||||
| 14. | See Figure 19. Install rubber grommet (3) into drilled hole. | |||||||||||
| 15. | See Figure 11. Install captive nuts (4) from inside of the large opening. | 
Figure 11. Captive Nuts | ||||||||||
| 16. | Repeat procedure for opposite side. | |||||||||||
| 17. | Install lower fairings. |
INSTALL
| 1. | Route speaker wire harness along the main harness in the wire trough toward the steering head. a. Harness connector should be located in the right side cover area. b. Harness speaker terminals should be located in the speaker enclosure areas. | |
| 2. | See Figure 12. Route speaker terminals (3) through the grommet in the lower fairing. a. Install speaker in the enclosure. See appropriate kit for installation. b. Wire lengths of the harness are the same length. Identify the right and left by wire color. c. Right: Light blue and light blue black. d. Left: Light blue/orange and light blue/gray. e. Leave enough slack in the harness to enable speaker removal. | |
| 3. | See Figure 13. Install lower fairing cap (2). | |
| 4. | Route and secure harness with cable straps. | |
| 5. | Repeat procedure for opposite side. | |
| 6. | See Figure 19. Connect [351B] of speaker wire harness (4) to: a. Primary Amplifier Installed: [351A] of the primary amplifier harness. b. Primary and Secondary Amplifiers Installed: [352A_1] or [352A_2] of the secondary amplifier of harness. c. Make harness connection in the right side cover area. |
| 1 | Speaker wire harness |
| 2 | Fairing cap |
| 3 | Speaker terminals |
Figure 12. Wire Harness Routing
| 1 | Fairing cap |
| 2 | Speaker wire harness |
| 3 | Harness routing |
Figure 13. Wire Harness Routing
COMPLETE
NOTE
To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.
| 1. | Install main fuse. | |
| 2. | Turn ignition ON, but do not start the vehicle. | |
| 3. | Make sure that all speakers are working and front/rear fader function is operating correctly. If not, check speaker wiring. | |
| 4. | Install wire trough cover. | |
| 5. | Install fuel tank. | |
| 6. | Install seat. | |
| 7. | Install left and right side covers. | |
| 8. | Install left and right saddlebags. |
APP SETUP
| 1. | Unresolved graphic link Accessing your audio system. | |
| 2. | Unresolved graphic link Main menu screen. a. Main menu icon (1). b. Reset or change security personal identification number (PIN) (2). c. Edit and rename your system (3). d. Customize main menu with your bike picture (4). | |
| 3. | Unresolved graphic link Setup menu screen. | |
| 4. | Unresolved graphic link Equalizer setup screen. | |
| 5. | Unresolved graphic link Diagnostic menu screen. a. Diagnostic menu icon (1) displays sound system status. b. Open the speaker testing screen (2). c. Refreshes speaker and amplifier status (3) after component repair. d. Select speaker for white noise (4) test and functionality. e. Return to diagnostic menu screen (5). |
| 1 | Diagnostic menu |
| 2 | Speaker test screen |
| 3 | Refresh status |
| 4 | Select a speaker to play white noise |
| 5 | Finish and return to diagnostic menu |
Figure 18. Diagnostic Menu
SERVICE PARTS
Figure 19. Service Parts, Fairing Lower Speakers
Table 2. Service Parts
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Screw, short (6) | 2995 |
2 | Gasket (2) | 25700895 |
3 | Grommet | 12100071 |
4 | Speaker wire harness | Not sold separately |
5 | Captive nut (4) | 10100064 |
6 | Screw, long (8) | 10200294 |
7 | Cable strap (10) | 10006 |
8 | Speaker enclosure, right | Not sold separately |
9 | Speaker enclosure, left | Not sold separately |