SADDLEBAG SPEAKER HARNESS INSTALL KIT (PN 76000979)
941001552021-02-04
GENERAL
NOTE
The newly installed audio system and speakers will not play audio unless it is configured using the Harley-Davidson audio app or by an authorized Harley-Davidson dealership.
Table 1.
Harley-Davidson Audio Powered by Rockford Fosgate® | |
|---|---|
Kit | QR Code |
76000979 | N/A |
NOTE
The various generations of speakers, amplifiers and wiring for Harley-Davidson vehicles were not designed or tested to work together. Please consult your dealership to ensure optimal performance and compatibility.
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Ensure you are using the most current version of the instruction sheet which is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
Download Harley-Davidson audio app.
Use this kit in conjunction with other Harley-Davidson Audio powered by Rockford Fosgate® kits.
This harness is for use ONLY on 2014 and later Harley-Davidson audio systems.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Primary Amplifier and Dongle Kit (Part No. 76000997) is required for this installation.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Primary Amplifier Installation Kit (Part No. 76000974 or 76001045) is required for this installation.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Secondary Amplifier Kit (Part No. 76000975) may be required for this installation. This depends if there are six speakers or more and how the amplifier channels are assigned.
- 2014 and Later FLHTKSE, FLTRUSE and Touring: Separate purchase of Harley-Davidson Stage 1 or 2 Speaker Kit (Part No. 76000986 or 76000987) may be required for this installation.
These items are available at your Harley-Davidson dealership.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
Installation by a technician at a Harley-Davidson dealership is recommended.
PREPARE
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
| 1. | Remove left and right saddlebags (excludes Tri-Glide). | |
| 2. | Remove left and right side covers. | |
| 3. | Remove main fuse. NOTE Models with security: Disable security system. | |
| 4. | Remove seat. |
RIGHT SADDLEBAG
NOTE
Drilling may vary by the number of speakers and amplifiers that are being installed. DO NOT drill any holes until the exact speaker installation is understood.
If only a primary amplifier is present in the left saddlebag, then drill only one ¾-inch opening as defined in Harness Install Without Secondary Amplifier.
If a secondary amplifier is present, then proceed to Harness Install With Secondary Amplifier and drill 2 holes using a hole saw.
Openings may already be present in the right saddlebag if a secondary amplifier was installed prior to this installation. In that case the template will not be used.
| 1. | See Figure 1. Position template (2) on right saddlebag (1). a. Use tape to secure template. | |
| 2. | NOTE Take extreme caution not to damage the painted surface. a. Center punch drill locations. b. Grommet hole: If only a primary amplifier is present and used, then use 19mm (3/4-in) drill bit. c. Internal harness hole: ONLY, if a secondary amplifier is present and used, then use 63.5 mm (2 ½-in) hole saw. d. De-burr hole by lightly sanding the surface. |
| 1 | Right saddlebag |
| 2 | Drill template |
| 3 | Dimple for drilling ¾-inch hole |
| 4 | 2 ½-inch hole (2)(secondary amplifier ONLY) |
Figure 1. Right Saddlebag Template
HARNESS INSTALL WITHOUT SECONDARY AMPLIFIER
NOTE
Remove amplifier cover from left saddlebag to access speaker connector under amplifier near the amplifier connector. The amplifier may be removed from the bracket for easier access.
| 1. | NOTE Amplifier may have to be removed from mounting bracket. a. See Figure 2. Locate wire harness 69202532 (2). b. See Figure 3. Disconnect speaker connector (1) from internal harness connector (2). c. Connect wire harness connector (2) to speaker connector (1). | |
| 2. | See Figure 4. Install left speaker wire harness. a. Route wire harness (1) as shown. b. Peel adhesive tape on harness wire conduit. c. Adhere harness wire conduit as shown. | |
| 3. | See Figure 5. Install right speaker wire harness. a. See Figure 2. Locate wire harness 69202533 (3). b. Route wire harness (2) as shown. c. Start with top harness wire conduit and work your way toward the grommet that passes through the saddlebag. NOTE Check harness placement BEFORE peeling tape backers and applying conduit to saddlebag. Harness length will be EXTREMELY difficult to adjust once multiple conduit pieces have been adhered in place. d. Peel adhesive tape on harness wire conduit. e. Adhere harness wire conduit as shown. f. Route wire harness (2) through grommet hole. g. Install grommet (3) on wire harness (2). h. Adjust grommet (3) as needed and install in saddlebag. | |
| 4. | See Figure 2. Locate wire harness 69202531 (4). a. Connect 4-way of 69202531 (4) to primary amplifier harness connector [351A] under right side cover. | |
| 5. | See Figure 5. Connect harnesses (1 and 2.) | |
| 6. | Secure harnesses with cable straps. a. Make sure there is sufficient wire length to so saddlebag can be removed and that the wire harness does not prevent any dynamic movement and has adequate clearance to all moving parts of vehicle. |
| 1 | Outline of left saddlebag lid |
| 2 | Wire harness 69202532 |
| 3 | Wire harness 69202533 |
| 4 | Wire harness 69202531 (use with all speaker setups) |
| 5 | Outline of right saddlebag lid |
Figure 2. Wire Harness Setup and Routing
| 1 | Speaker connector |
| 2 | Internal harness connector |
| 3 | Wire harness 69202532 connector |
Figure 3. Left Saddlebag Speaker Connection
| 1 | Wire harness 69202532 |
| 2 | Left saddlebag (shown without amplifier installed) |
Figure 4. Left Saddlebag Harness Routing
| 1 | Wire harness 69202531 (use with all speaker setups) |
| 2 | Wire harness 69202533 |
| 3 | Grommet |
| 4 | Right saddlebag |
Figure 5. Right Saddlebag Harness Routing (Without Amplifier)
HARNESS INSTALL WITH SECONDARY AMPLIFIER
NOTE
If Tour-Pak speakers or fairing lower speakers were connected to the primary amplifier prior to this installation, they must be disconnected from the primary amplifier harness at [351]. They will be re-connected to the secondary amplifier harness at [352A_2] and [352A_2].
Remove amplifier cover from left saddlebag to access speaker connector under amplifier near the amplifier connector. The amplifier may be removed from the bracket for easier access.
NOTE
If the secondary amplifier has not yet been installed, see instructions in that kit to drill 2 ½-inch holes in the right saddlebag with a hole saw. See Figure 1.
| 1. | Connect speaker wire harness to amplifier in left saddlebag. a. See Figure 6. Locate wire harness 69202532 (2). b. See Figure 3. Disconnect speaker connector (1) from internal harness connector (2). c. Connect wire harness connector (2) to speaker connector (1). | |
| 2. | See Figure 8. Install left speaker wire harness. a. Route wire harness (1) as shown. b. Peel adhesive tape on harness wire conduit. c. Adhere harness wire conduit as shown. d. Reinstall amplifier and cover (if removed) in left saddlebag. Torque: 13.5 N·m (119 in-lbs) | |
| 3. | Connect speaker wire harness to amplifier in right saddlebag. a. See Figure 6. Locate wire harness 69202532 (3). b. See Figure 7. Connect wire harness connector (2) to speaker connector (1). | |
| 4. | See Figure 9. Install right speaker wire harness. a. Route wire harness (3) as shown. b. Peel adhesive tape on harness wire conduit. c. Adhere harness wire conduit as shown. | |
| 5. | See Figure 6. Locate wire harnesses 69202563 (4) and 69202531 (5). | |
| 6. | See Figure 9. Connect harnesses 69202531 (1) and 69202563 (2) together. a. Connect 4-way end of 69202531 (1) to primary amplifier harness connector [351A] under right side cover. | |
| 7. | Connect harness 69202563 (2) to saddlebag. | |
| 8. | Secure harnesses with cable straps. | |
| 9. | Install amplifiers and covers, if removed. a. Tighten cover screws. Torque: 13.5 N·m (119 in-lbs) Amplifier cover screw |
| 1 | Outline of left saddlebag lid |
| 2 | Wire harness 69202532 |
| 3 | Wire harness 69202532 |
| 4 | Wire harness 69202563 (use with 6 and 8 speaker setup) |
| 5 | Wire harness 69202531 (use with all speaker setups) |
| 6 | Outline of right saddlebag lid |
Figure 6. Wire Harness Setup and Routing
| 1 | Speaker connector |
| 2 | Wire harness 69202532 connector |
Figure 7. Left Saddlebag Speaker Connection, Right is Similar
| 1 | Wire harness 69202532 |
| 2 | Left saddlebag (shown without amplifier installed) |
Figure 8. Left Saddlebag Harness Routing
| 1 | Wire harness 69202531 (use with all speaker setups) |
| 2 | Wire harness 69202563 |
| 3 | Wire harness 69202532 |
| 4 | Right saddlebag |
Figure 9. Right Saddlebag Harness Routing (With Amplifier)
SPEAKER HARDWARE
| 1. | See Figure 15. Use speaker hardware screws and grommets (8, 9, 10) to install speakers. | |
| 2. | See speaker kit for instructions and torque values. |
COMPLETE
NOTE
To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.
| 1. | Install main fuse. | |
| 2. | NOTE Before installing outer fairing, check that speakers are operating correctly. Understand that buzzing, squeaks and rattles may be heard until outer fairing is installed. | |
| 3. | Make sure that all speakers are working and front/rear fader function is operating correctly. If not, check speaker wiring. | |
| 4. | Install seat. | |
| 5. | Install left and right side covers. | |
| 6. | Install left and right saddlebags (excludes Tri-Glide). |
APP SETUP
| 1. | Unresolved graphic link Accessing your audio system. | |
| 2. | Unresolved graphic link Main menu screen. a. Main menu icon (1). b. Reset or change security personal identification number (PIN) (2). c. Edit and rename your system (3). d. Customize main menu with your bike picture (4). | |
| 3. | Unresolved graphic link Setup menu screen. | |
| 4. | Unresolved graphic link Equalizer setup screen. | |
| 5. | Unresolved graphic link Diagnostic menu screen. a. Diagnostic menu icon (1) displays sound system status. b. Open the speaker testing screen (2). c. Refreshes speaker and amplifier status (3) after component repair. d. Select speaker for white noise (4) test and functionality. e. Return to diagnostic menu screen (5). |
| 1 | Diagnostic menu |
| 2 | Speaker test screen |
| 3 | Refresh status |
| 4 | Select a speaker to play white noise |
| 5 | Finish and return to diagnostic menu |
Figure 14. Diagnostic Menu
SERVICE PARTS
Figure 15. Service Parts, Fairing Lower Speakers
Table 2. Service Parts
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Grommet | 12100167 |
2 | Drill template | 76001009 |
3 | Internal speaker wire harness, right saddlebag (use with 4 speaker system only) | Not sold separately |
4 | Internal speaker wire harness, left saddlebag (2) | Not sold separately |
5 | Jumper wire harness, long (use with all speaker setup) | Not sold separately |
6 | Jumper wire harness, short (use with 6 and 8 speaker setup) | Not sold separately |
7 | Cable strap (10) | 10006 |
8 | Screw, short (8) | 10200351 |
9 | Washer, rubber (8) | 10300066 |
10 | Screw, long (8) | 10200095 |
Items mentioned in the instruction but not included in kit. | ||
A | Saddlebag lid | |