DOCKING HARDWARE KIT

941001662022-02-23

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
52300705	Safety Glasses, Torque Wrench, Loctite 243, PJ1 cleaner

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Docking Hardware Kit

Table 2. Kit Contents: Docking Hardware Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	2	Docking hardware, black	52300704
2	2	Screw, black	10201091	15–18.3 N·m (11.1–13.5 ft-lbs)

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)

PREPARE

To attain proper clamp load, always clean fastener threads and threaded holes prior to assembly.

Always verify cleanliness of blind holes before assembly. Tightening a screw with dirt, water or oil in the hole can cause castings to crack or break.

NOTE

Never use a thread-cutting tap or die to clean threads.

1.	See Figure 2. Remove and discard rear Original Equipment (OE) fender strut screws (1).
2.	Clean threadlocking material from threaded holes. a. Use a thread chaser to clean threaded holes. b. Use PJ1 cleaner or equivalent to remove all traces of oil and contaminants from threads.PJ1 SUPER CLEANER (99878-87TA) c. Clear all threaded holes with low-pressure compressed air.

Screw (2)

Figure 2. OE Fender Strut Screw

INSTALL

1.	See Figure 3. Apply threadlocker to screw (2).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
2.	Install docking points (1). a. Rotate docking point so "T"s are on top and bottom.
3.	Install screw (2). Finger tighten.
4.	Repeat procedure for left side.
5.	Test fit attachment.
6.	Adjust docking points.

1	Docking point
2	Screw

Figure 3. Docking Hardware Install

ADJUST DOCKING POINT

NOTE

If attachment rattles once installed, docking points must be adjusted. The docking point is elliptical. When "T"s on docking point are on top and bottom, docking point fit is at its loosest. When "T"s are at front and rear, docking point fit is at its tightest.

1.	Remove attachment.
2.	See Figure 4. To adjust, rotate (3) in small increments so the "T" (1) is no longer on top and approaches either position (2).
3.	At each increment, check fit with attachment.
4.	Continue rotation in small increments and test until desired tightness is achieved. The tightest possible position is when the "T"s reach position (2).
5.	See Figure 3. Tighten docking point screws (2). Torque: 15–18.3 N·m (11.1–13.5 ft-lbs)
6.	Install attachment.

1	Loosest position (T location)
2	Tightest position (T location)
3	Possible rotation direction

Figure 4. Docking Point Flats

MAINTENANCE

In time docking points wear, causing installed detachable accessory to become loose and rattle. Tighten the fit using the following method.

1.	Record current "T" position for each docking point.
2.	Remove screw from docking point.
3.	Remove threadlocker from docking point screw(s) and mounting hole thread(s).
4.	Apply 2 or 3 drops of threadlocker to threads of docking point screw(s).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
5.	Install docking points and screws. Finger tighten.
6.	See Figure 4. If "T"s are not in tightest position (2), rotate docking points slightly, moving "T"s toward (2) until a tight fit of attachment is achieved at each location.
7.	Tighten docking point screws.
8.	If docking point "T"s are in position (2): a. Remove screw from rear docking points. b. Rotate each docking point until "T" on opposite side reaches loosest position (1). c. Remove threadlocker from docking point screw(s) and mounting hole thread(s). d. Apply 2 or 3 drops of threadlocker to threads of docking point screw(s).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) e. Install docking points and screws. Finger tighten. f. Check attachment at each docking point, rotating the "T" toward (2) until a tight fit of attachment is achieved at each location. g. Secure docking point screws. Tighten.
9.	After multiple adjustments, if the detachable accessory continues to rattle or remains loose, replace the docking points.