SISSY BAR

941001722022-07-20

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
52300700, 52300702	Safety Glasses

(1) Only simple tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Sissy Bar (tall upright shown)

Table 2. Kit Contents: Sissy Bar Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Medallion	13883-00
2	2	Passenger backrest, short	52300698
2	2	Passenger backrest, tall	52300694
3	4	Plug, black	12100176
4	2	Plug	12100105
5	1	Grommet, side plate, left	52300712
6	1	Grommet, side plate, right	52300738
7	1	Latch lever assembly, left	52300496
8	1	Latch lever assembly, right	52300494

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

See Docking Hardware Kit 52300705 should docking points require maintenance or replacement.

WARNING

Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)

REMOVE

1.	See Figure 2. Pull both detent levers (3) rearward from locked position (2), against compression spring (8).
2.	Rotate detent levers upward while pulling on levers. a. As levers rotate upward, latch noses (4) are forced against rear docking points (Figure 2, item 13). b. This raises rear of backrest side plates (6) out of docking points.
3.	Release detent levers. a. Springs (8) will move each lever back into unlocked position (1).
4.	Pull backrest side plates away from front shock docking points. Do not exceed angle shown in Figure 2.
5.	Remove backrest from vehicle.

INSTALL

1.	See Figure 1. Position right (8) and left (7) latch levers in unlocked position. a. See Figure 2. Pull both detent levers (3) rearward against compression spring (8 not visible). b. Rotate levers upward so each latch nose (4) is positioned inside lower rear notch (9) of side plate (6). c. Each detent pin (7) is now located in uppermost (unlocked position) notch. d. Compression spring (8) inside detent lever holds latch (5) in unlocked position.
2.	Push side plate front notches (10), with grommets (11) in place, firmly and evenly into front shock docking points (12).
3.	Swing rear of backrest side plates (6) downward toward rear docking points (13). a. As side plates (6) move down, latches make contact with plastic surface of rear docking points.
4.	As docking points contact latches, each latch nose (4) is forced upward. a. This causes pin (7) to move down into lowermost (2-locked) position on side plate. b. Springs (8) lock each latch firmly in place around rear docking points. c. You should hear an audible click as latches engage docking points.
5.	Make sure that detent pins (7) are fully seated against side plates (6). a. If not fully seated, push detent lever (3) forward. b. If still not fully seated, docking point may need to be rotated. See Docking Hardware Kit instructions.

1	Unlocked position
2	Locked position
3	Detent lever
4	Latch nose
5	Latch
6	Side plate
7	Detent pin
8	Compression spring (not shown)
9	Side plate lower rear notch
10	Side plate front notch (not shown)
11	Grommet (not shown)
12	Front docking point
13	Rear docking point

Figure 2. Detachable Backrest Remove/Install

MAINTENANCE

In time docking points wear, causing rack to become loose and rattle. Tighten using maintenance procedure found in Docking Hardware Kit 52300705.