RIDER AND PASSENGER FOOTPEGS

941001982022-08-08

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
50502148, 50502149, 50502150, 50502151, 50502338, 50502339, 50502353, 50502354	Safety Glasses, Torque Wrench, Loctite 243 Blue

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Footpegs - Rider & Passenger

Table 2. Kit Contents: Footpegs - Rider & Passenger Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Footpeg assembly, rider, right	50502184	Kit 50502148
			50502186	Kit 50502149
			50502193	Kit 50502150
			50502341	Kit 50502338
			50502342	Kit 50502339
		Footpeg assembly, passenger, right	50502195	Kit 50502151
			50502356	Kit 50502353
			50502357	Kit 50502354
2	1	Footpeg assembly, rider, left	50502185	Kit 50502148
			50502187	Kit 50502149
			50502194	Kit 50502150
			50502347	Kit 50502338
			50502348	Kit 50502339
		Footpeg assembly, passenger, left	50502196	Kit 50502151
			50502362	Kit 50502353
			50502363	Kit 50502354
3	2	Screw, adjustment	10201142	40.5 N·m (30 ft-lbs)
4	2	Wear peg	50502198	Kit 50502149
			50501536	Kit 50502150
			50500628	Kits 50502338, 50502339
5	2	Detent	50502231	Kits 50502151, 50502353, 50502354

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)

INSTALL

RIDER

1.	See Figure 2. Remove pin (4) and retaining clip (2). Retain. a. Save all hardware including torsion spring (1) for installation on new footpegs (3).
2.	Insert short leg of torsion spring (1) into hole in new footpeg (3). NOTE When performing next step, verify that spring is positioned inside of footpeg.
3.	Align long leg of torsion spring (1) to hole in footpeg mount and insert.
4.	Rotate footpeg into position in clevis.
5.	Insert pin (4) through clevis, footpeg (3) and spring (1).
6.	Install retaining clip (2).
7.	Repeat on opposite side.
8.	Adjust orientation: (if design allows) a. Forward controls: foot surface to be parallel to mounting pin. b. Mid controls: foot surface to be parallel to ground.
9.	See Figure 1. Tighten adjustment screw (3). Torque: 40.5 N·m (30 ft-lbs)

1	Torsion spring
2	Retaining Clip
3	Footpeg
4	Pin

Figure 2. Rider Footpeg Torsion Spring Install

PASSENGER

1.	See Figure 3. Remove pin (1) and retaining clip (5). Retain. NOTE When performing next step, verify that spring (3) is positioned inside of footpeg. a. Save all hardware including detent spring (3), detent ball (4) and detent plate (6) for installation of new footpegs.
2.	Insert detent spring (3) into new footpeg (2).
3.	Insert detent ball (4).
4.	Position detent plate (6) onto footpeg clevis edge, capturing detent ball (4) and detent spring (3) inside detent plate (6). NOTE Certain models require use of detent plate from kit, including Sportster S and Nightster.
5.	Install detent from kit, orienting notch upwards.
6.	Slide detent plate (6) onto footpeg clevis.
7.	Align detent plate (6) and footpeg (2) with footpeg mount on vehicle.
8.	Install pin (1) and retaining clip (5).
9.	Adjust orientation: (if design allows) a. Rotate to desired orientation. b. Fold peg up to stowed position and confirm clearance to other components. c. Adjust as necessary. NOTE If there is contact on Screamin Eagle exhaust or if footpeg hits lock position too soon, remove and flip detent plate (6) over. d. See Figure 1. Tighten adjustment screw (3). Torque: 40.5 N·m (30 ft-lbs)

1	Pin
2	Footpeg
3	Detent spring
4	Detent ball
5	Retaining clip
6	Detent plate

Figure 3. Passenger Footpeg Detent Spring Install

WARNING

Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a)

WEAR PEG REPLACEMENT

1.	See Figure 1. Remove existing wear peg (4) from footpeg.
2.	Apply two or three drops of threadlocker to wear peg (4).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
3.	Install wear peg (4) to footpeg. Tighten. Torque: 4.52–5.08 N·m (40–45 in-lbs)