Screamin' Eagle Quickshifter - Pan America models
941002432023-09-13
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
32700151 | Safety Glasses, Torque Wrench |  |
(1) DTII and dealer installation required
KIT CONTENTS
Figure 1. Kit Contents: Screamin' Eagle Quickshifter
Table 2. Kit Contents: Screamin' Eagle Quickshifter Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Sensor | 32700148 | |
| 2 | 1 | Cable strap | 10177 | |
| 3 | 1 | Cable strap | 10006 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
PREPARE
| 1. | Remove main fuse. |
REMOVE
| 1. | Remove skid plate. See service manual. | |
| 2. | See Figure 2. Remove front shifter linkage screw (7). | |
| 3. | See Figure 2. Remove shifter lever pivot screw (5), washer (4) and nut (3). | |
| 4. | See Figure 2. Remove shifter lever (1) and shifter linkage (6) from frame boss. | |
| 5. | See Figure 2. Remove Screw (2) from shifter linkage (6) from shifter lever (1). |
| 1 | Shifter lever |
| 2 | Screw |
| 3 | Nut |
| 4 | Washer |
| 5 | Pivot screw |
| 6 | Shifter linkage |
| 7 | Screw |
Figure 2. Shifter Lever / Shifter Linkage Removal
INSTALL
| 1. | See Figure 3. Assemble quick shifter sensor (1) to shifter lever (3) with screw (2). Tighten. Torque: 10.5–12 N·m (93–106 in-lbs) | |
| 2. | NOTE If transmission shift shaft lever is off ONE SPLINE in either direction from the six o'clock position, it is in the incorrect location. a. Deviation from this position, either forward or backward, may adversely affect operation of the quick shifter. b. If the shift shaft lever is not at the six o'clock position, see service manual to correctly orientate the transmission shift shaft lever. | |
| 3. | NOTE Preferred orientation of quick shifter sensor is shown. Make sure wire harness is routed properly to avoid excessive loops. Torque: 24.5–30 N·m (18–22 ft-lbs) | |
| 4. | Install screw (7) to front of quick shifter (6) to transmission shift arm (2). Tighten. Torque: 10.5–12 N·m (93–106 in-lbs) | |
| 5. | Connect quick shifter sensor to engine harness. | |
| 6. | Vehicles with side stand switch harness. a. Remove cable strap from side stand switch harness. b. See Figure 7. Connect quick shifter harness and side stand harness with cable strap (3) loosely. c. Connect quick shifter harness and side stand frame mount with cable strap (2) loosely. d. Ensure routing of quick shifter harness clears skid plate, side stand and oil filter. e. Ensure up/down shifts are completing the full range of motion and not pulling on harness. NOTE Check for contact between shifter lever and quick shifter sensor body. f. Tighten both cable straps (2,3). | |
| 7. | Vehicles without side stand switch harness. a. See Figure 7. Connect quick shifter harness side stand bracket with cable strap (3) loosely. b. Connect quick shifter harness and side stand frame mount with cable strap (2) loosely. c. Ensure routing of quick shifter harness clears skid plate, side stand and oil filter. d. Ensure up/down shifts are completing the full range of motion and not pulling on harness. NOTE Check for contact between shifter lever and quick shifter sensor body. e. Tighten both cable straps (2,3). | |
| 8. | Install skid plate. See service manual. |
| 1 | Quick shifter |
| 2 | Screw |
| 3 | Shifter lever |
Figure 3. Install Quick Shifter to Shifter lever
| 1 | Six o'clock position |
Figure 4. Correct Transmission Shift Shaft Lever Position
NOTE
If transmission shift shaft lever is off ONE SPLINE in either direction from the six o'clock position, it is in the incorrect location.
| 1 | Forward deviation |
| 2 | Backward deviation |
Figure 5. Incorrect Transmission Shift Shaft Lever Positions
| 1 | Shifter lever |
| 2 | Transmission shift shaft lever |
| 3 | Pivot screw |
| 4 | Washer |
| 5 | Nut |
| 6 | Quick shifter |
| 7 | Screw |
Figure 6. Quickshifter Install
| 1 | Harness connection [348B] |
| 2 | Cable strap (P/N 10177) |
| 3 | Cable Strap (P/N 10006) |
| 4 | Shifter lever |
| 5 | Quick shifter |
Figure 7. Quickshifter
COMPLETE
| 1. | Install main fuse. |
COMPLETE
Have a Harley-Davidson dealer update software using DIGITAL TECHNICIAN II (Part Number:HD-48650) to enable quick shifter functionality.