0/0
REAR WHEEL
941002712021-08-02
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
40900871
Safety Glasses
(1) Only simple tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Rear Wheel
Table 2. Kit Contents: Rear Wheel Kit
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Wheel
Not sold separately
Items mentioned in text, but not included in kit
A
2
Original Equipment (OE) Bearing, regular, See Table 3 and Table 4
B
1
OE Bearing, ABS***, Refer to Table 3.
C
1
OE Axle sleeve, See Table 3 and Table 4
D
1
OE Axle sleeve, See Table 3 and Table 4
H
1
OE Valve stem, See Table 3 and Table 4
Table 3. REAR 25mm Bearing Wheel Installation Kit (41456-08C)
REAR 25 MM Bearing Non-ABS Wheel Installation Kit (41456-08C)
Item (Quantity Used and Description)
Fitment
Wheel Size
A
C
D
E
F
H
I
J
2009 and later FLT non-ABS
16 x 5.0 in
2
1
0
0
0
*
*
*
2009 and later FLT non-ABS
18 x 5.0 in
2
1
0
0
0
*
*
*
2008 VRSCD non-ABS
18 x 5.5 in
2
0
0
1
**
*
*
0
2008 and later FXCW and FXCWC non-ABS
18 x 8.0 in
2
0
1
0
0
*
*
0
2008 - 2017 VRSCAW, VRSCDX and VRSCF non-ABS
18 x 8.0 in
2
0
0
1
**
*
*
0
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
* See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
** See INSTALLATION to determine if shim is required.
*** Bearing shim installed under primary bearing.
A
Bearing, regular (2)
9276B
C
Axle sleeve
41349-07
D
Axle sleeve
41358-08
E
Axle sleeve
43704-08
F
Bearing shim***
41447-08
H
Valve stem, short
43157-83A
I
Valve stem, long
43206-01
J
Valve stem, pull thru
40999-87
Table 4. REAR 25 MM Bearing ABS Wheel Installation Kit (41453-08C)
REAR 25 MM Bearing ABS Wheel Installation Kit (41453-08C)
Item (Quantity Used and Description)
Fitment
Wheel Size
A
B
C
D
E
F
G
H
I
J
2008 FLT with ABS
16 x 3.0 in
1
1
0
1
0
0
1
*
*
0
2009 and later FLT with ABS
16 x 5.0 in
1
1
1
0
0
0
0
*
*
*
2009 and later FLT with ABS
18 x 5.0 in
1
1
1
0
0
0
0
*
*
*
2008 VRSCDa with ABS
18 x 5.5 in
1
1
0
0
1
**
0
*
*
0
2008 - 2017 VRSCAWa, VRSCDXa, VRSCXa and VRSCFa with ABS
18 x 8.0 in
1
1
0
0
1
**
0
*
*
0
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
* See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
** Primary bearing. Bearing must be installed with red side facing the wheel.
*** Bearing shim installed under primary bearing.
A
Bearing, regular
9276B
B
Bearing, ABS**
9252A
C
Axle sleeve
41349-07
D
Axle sleeve
41900-08
E
Axle sleeve
43704-08
F
Bearing shim***
41447-08
G
Bearing shim***
43904-08
H
Valve stem, short
43157-83A
I
Valve stem, long
43206-01
J
Valve stem, pull thru
40999-87
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
WARNING
Install only wheels and installation kits approved for your model motorcycle. Contact a Harley-Davidson dealer to verify fitment. Mismatching wheels and installation kits or installing wheels not approved for your model can cause loss of control, which could result in death or serious injury. (00610c)
Proper installation of this kit requires separate purchase of the following parts which are available at a Harley-Davidson dealer:
The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning:
PREPARE
NOTE
  • Prior to removing or installing wheel, rear brake caliper must be removed.
  • Cotter pin or spring clip for axle nut must be replaced. They are available for purchase from your dealer. See your dealer for correct part number for your model vehicle.
    • If vehicle is equipped with TPMS use TPMS valve stem. If vehicle is not equipped with TPMSinstall pull thru valve stem (40999-87) included in installation kit. Discard all other valve stems.
NOTICE
Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c)
NOTICE
Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b)
REMOVE
1. Remove existing rear wheel assembly. See service manual.
a. Save axle, axle nut, brake disc, sprocket and wheel spacers for kit installation.
Table 5. Rear Disc and Sprocket Hardware Fitment
Hardware
Fitment
Rear Disc Screws (select stock or chrome hardware)
5 Stock disc screws (43567-92)
All models
Chrome screw kit (46647-05) includes 5 screws
All models
INSTALL
NOTE
  • Install primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER.
  • Right side of rear wheel has brake rotor and is the primary bearing side.
  • Bearing shims provided in installation kit are not required and can be discarded.
1. See Table 3 and Table 4. Assemble wheel installation kit components to wheel using appropriate service parts table. See service manual.
2. Refer to Tire Mounting. Install tire on wheel.
3. Install rear wheel (1), stock axle and stock spacers. See service manual.
WARNING
After repairing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a)
WARNING
Whenever a wheel is installed and before moving the motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00284a)
Tire Mounting
NOTE
If vehicle is equipped with TPMS use TPMS valve stem. Valve stem points toward high side of vehicle when installed. If vehicle is not equipped with TPMS install pull thru valve stem (40999-87) included in installation kit. Discard all other valve stems.
1. See Figure 1. Install valve stem (H) on rear wheel. See service manual.
2.
NOTE
  • Only install the required (separately purchased) tire.
  • If wheel has a yellow dot sticker on rim, orient tire so white dot on tire is opposite of sticker. If wheel has a green dot sticker on rim, orient tire so white dot on tire is aligned with sticker. If no rim dot sticker is present, see service manual.
  • Use plastic protectors on tire mounting tools and rim clamps when mounting a tire to a painted wheel.
  • When mounting tires, liberally use tire lube on wheel and tire.
Mount new rear tire (purchased separately) to wheel. See service manual.
a. Rear Tire: 43200045
3. Install stock rear brake disc and sprocket on wheel using new hardware. See service manual.
4. Return to INSTALL.
MAINTENANCE
Wheels must be maintained regularly to keep their original shine and luster.
1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel & Tire Cleaner. Apply with Harley® Wheel and Spoke Brush.
2. Thoroughly clean wheel with a good quality cleaner, such as Wheel & Tire Cleaner.
3. After cleaning and polishing, seal finish with a good quality sealer, such as Glaze Poly Sealant.