PASSENGER FOOTPEG MOUNT KIT WITH FOOTPEGS
941002812022-03-07
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
50502434 | Safety Glasses, Torque wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Aggressive Edge Footpegs - Rider
Table 2. Kit Contents: Rider Footpegs Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Bracket, footpeg, left | 50502088 | |
| 2 | 1 | Bracket, footpeg, right | 50502086 | |
| 3 | 4 | Screw | 10200929 | |
| 4 | 1 | Footpeg assembly, left | 50502132 | |
| 5 | 1 | Footpeg assembly, right | 50502197 | |
| 6 | 2 | Detent plate | 50500705 | |
| 7 | 2 | Detent spring | 50500706 | |
| 8 | 2 | Detent ball | 50500707 | |
| 9 | 2 | Clevis pin | 50501782 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit.
If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation.
Improper installation of this kit could result in death or serious injury. (00308b)
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
REMOVE
| 1. | See Figure 2 and Figure 3. Remove side covers (1) to access frame side mount holes. See service manual. | |
| 2. | See Figure 2 and Figure 3. Remove screw in side covers to release punchouts (2). | |
| 3. | Disconnect and remove exhaust from right side bracket. See service manual. |
INSTALL
| 1. | See Figure 4. Install left footpeg mounting bracket (1) and screws (2). Tighten. Torque: 21–25 N·m (15–18 ft-lbs) | |
| 2. | See Figure 2. Install left side cover (1). | |
| 3. | See Figure 5. Install right footpeg mounting bracket (1) and screws (2). Tighten. Torque: 21–25 N·m (15–18 ft-lbs) | |
| 4. | See Figure 3. Install right side cover (1). | |
| 5. | See Figure 5. Install exhaust to right side bracket. See service manual. a. Secure with Original Equipment (OE) screw (4) and nut (5). Tighten. Torque: 19–27 N·m (14–20 ft-lbs) | |
| 6. | See Figure 6. Install left footpeg (1) to new footpeg mounting bracket (3). NOTE When performing the next step, verify that spring (7) and ball (6) are positioned inside of footpeg (1). a. Insert detent spring (7) into footpeg (1), followed by detent ball (6). b. Slide detent (5) on footpeg (1) while capturing detent ball (6) and detent spring (7). c. Align detent (5) and footpeg (1) with footpeg mounting bracket (3) on vehicle. d. Install clevis pin (8). | |
| 7. | See Figure 6. Install right footpeg (2) to new footpeg mounting bracket (4). NOTE When performing the next step, verify that spring (7) and ball (6) are positioned inside of footpeg (2). a. Insert detent spring (7) into footpeg (2), followed by detent ball (6). b. Slide detent (5) on footpeg (2) while capturing detent ball (6) and detent spring (7). c. Align detent (5) and footpeg (12) with footpeg mounting bracket (4) on vehicle. d. Install clevis pin (8). |
| 1 | Side cover |
| 2 | Punchout |
| 3 | Footpeg mounting bracket |
Figure 2. Left Side Cover Remove/Install
| 1 | Side cover |
| 2 | Punchout |
| 3 | Footpeg mounting bracket |
Figure 3. Right Side Cover Remove/Install
| 1 | Footpeg mounting bracket |
| 2 | Screw (2) |
Figure 4. Left Side Footpeg Mounting Bracket Install
Figure 5. Right Side Footpeg Mounting Bracket Install
| 1 | Footpeg, left |
| 2 | Footpeg, right |
| 3 | Footpeg mounting bracket, left |
| 4 | Footpeg mounting bracket, right |
| 5 | Detent |
| 6 | Detent ball |
| 7 | Detent spring |
| 8 | Clevis pin |
Figure 6. Footpeg Install