SECURITY ANCHOR INSTALLATION KIT

941002882022-01-17

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
12600354	Safety Glasses, Power drill, 10 mm or 25/64" drill bit, Wrench (17 mm, socket or adjustable), Hammer, Screwdrivers (Flat & Phillips head), 6mm Hex wrench, Felt Marker, Anti-corrosion paint/sealer, Epoxy (optional)

(1) Only simple tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Security Anchor Installation Kit

NOTE

Verify all contents are present in the kit before installing or removing items from vehicle.

Table 2. Kit Contents: Security Anchor Installation Kit

Item	Qty	Description	Part No.
1	1	Mounting plate	Not sold separately
2	4	Nut, hex	Not sold separately
3	4	Washer, flat	Not sold separately
4	2	Washer, lock	Not sold separately
5	2	Nut, rivet	Not sold separately

NOTE

Verify all contents are present in the kit before installing or removing items from vehicle.

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

Separate purchase of Security Anchor Kit (92800013) is required.

Two people are recommended for the installation of this kit.

This kit is not intended to be used as a tie-down. Anchor is only intended to serve as a loop point for a lock.

NOTE

Failure to follow these instructions could lead to equipment or property damage as well as potentially hazardous conditions, which if not avoided or corrected, may cause death or serious injury.

PREPARE

1.	Choose location to permanently mount ground anchor.
2.	Verify that ground anchor is flat on truck bed/trailer surface.
3.	See Figure 2. Ensure space between baseplate and steel baseplate assembly is less than 48 mm (1.9 in). This is to ensure that nuts have proper amount of thread.

1	Truck bed/Trailer
2	Expanding shield nut
3	48 mm (1.9") Space between baseplates

Figure 2. Security Anchor Baseplate/Steel Baseplate

INSTALL

1.	See Figure 6. Remove cover (4) by placing a flat head screw driver under slot slowly (on both sides) until it pops out.
2.	Outline baseplate (3) and center point of one hole with felt marker on desired location.
3.	See Figure 1. Take mounting plate (1) and check underneath vehicle or trailer to make sure it does not interfere with any gas lines or electrical lines. NOTE Test marked center point by using a smaller drill bit as a pilot hole and very carefully drill until it completely goes through material you are drilling into. Careful not to have any sharp edges left around holes if drilling through metal.
4.	See Figure 1. Recheck to ensure that mounting plate (1) is not obstructed underneath. a. If OK continue to Step 5. b. If NOT repeat Step 1.
5.	Drill hole straight and vertical completely through truck bed/trailer on center point of marked hole.
6.	See Figure 6. Place baseplate (3) over outlined mark made earlier.
7.	Mark center point of next hole.
8.	Drill hole.
9.	Repeat steps (6-8) two more times.
10.	After drilling into truck or trailer bed, add a coating of anti-corrosion paint or sealer on top and bottom of drilled holes. This is to help prevent rusting.
11.	See Figure 3. Install baseplate (3) and four hex head bolts (1).
12.	See Figure 3 and Figure 4. Install mounting plate (4) to underside of truck bed/trailer.
13.	Install washer (2) and locknut (3). Tighten until snug.
14.	Repeat step 13 on next bolt diagonal from one just install.
15.	For permanent installation/added protection: See Figure 3 and Figure 4. Install washer (2), split washer (4) and anti-tamper security break-off nut (5) to remaining bolts. NOTE Verify that plate stays in place while tightening.
16.	See Figure 4. Secure hex head bolts (1) in place with 6 mm Allen wrench, tighten all lock nuts (3) evenly with a wrench until snug.
17.	See Figure 4. Tighten both anti-tamper security break-off nuts (5) by tightening up to 3 turns each until snug.
18.	Once snug apply turning force to wrench until anti-tamper security break-off nuts (5) breaks apart. This makes nuts permanently fixed. NOTE This is the anti-theft part that will stop someone from undoing base plate from truck bed/trailer floor. For extra security, add epoxy to cover/fill in area.
19.	See Figure 5. Install security ball bearing (1) into top of hex head bolt (2) cavity. a. With hammer, tap expanding shield nuts (3) as far as it will go.
20.	Repeat step (19) for remaining three bolts.
21.	See Figure 6. Install cover (2) over U-bolt (3) on baseplate.
22.	See Figure 6. Install bolts (1). Tighten until snug.
23.	See Figure 6. Install cover (4) and plugs into open holes. a. Push plugs in with even thumb pressure.

1	Bolt (4)
2	Baseplate, security anchor
3	Truck bed/Trailer
4	Mounting plate

Figure 3. Security Anchor Installation Truck Bed/Trailer

1	Mounting plate
2	Washer (4)
3	Nut (4)
4	Washer, split (2)
5	Security break-off nut (2)

Figure 4. Baseplate Installation

1	Security ball bearing (4)
2	Bolt (4)
3	Expanding shield nut (4)

Figure 5. Hardened Security Ball Bearing

1	Bolt, phillips head (2)
2	Cover, security
3	U-bolt/base plate
4	Cover, logo

Figure 6. Security Anchor Installation

LIFETIME LIMITED PRODUCT WARRANTY:

Schlage Lock Company, LLC, through its Kryptonite division (“Kryptonite”) extends a limited lifetime warranty to original user of products manufactured by Kryptonite (“Products”) against defects in material and workmanship. This warranty only applies to Original User of Products. This warranty is not transferable. This warranty gives you specific legal rights, and you may also have other rights, which vary from location to location. For complete warranty information and additional terms and conditions please visit Kryptonite’s website at www.kryptonitelock.com or call Kryptonite at 1-800-729-5625 (USA Only) or 001 781-828-6655. To contact Kryptonite, go to www.kryptonitelock.com or call 1-800-SAY-LOCK (USA Only) or 001 781-828-6655.