TURN SIGNAL RELOCATION KIT

941003592023-01-09

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
67801349	Safety Glasses, Torque Wrench, Fish Tape

(1) Special tools or techniques required for installation

KIT CONTENTS

Figure 1. Kit Contents: Turn signal Relocation Kit

Table 2. Kit Contents: Turn signal Relocation Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	2	Cover, fender support	57300404
2	2	Anchored cable strap	12500001
3	2	Screw, button head	10200589
4	1	Gasket, housing	Not sold separately
5	2	Cable strap	10126
6	1	Housing, turn signal	Not sold separately
7	1	Extension harness kit	69200150	Includes: 72 inch PVC tube, 24 inch wire length, 42 inch wire length, butt splice connectors, #16-20 AWG terminal pins

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

PREPARE

1.	Remove main fuse. See service manual.
2.	Remove seat. See service manual.
3.	Remove rear fender. See service manual.

REMOVE

1.	Remove rear turn signal lamp assemblies from fender supports. See service manual. a. Save turn signal lamp housings for later use. b. Discard turn signal standoffs.
2.	Remove tail lamp assembly. a. See Figure 2. Remove screws (1). b. Separate tail lamp lens (2) from base assembly. c. See Figure 3. Disconnect tail lamp (1) connector. d. Disconnect connectors (2, 3, 4). e. See Figure 4. Remove screw (1) and base assembly (2). f. Discard base assembly (2) with circuit board.

1	Screw (2)
2	Tail lamp lens

Figure 2. Tail Lamp Lens

1	Tail lamp [93]
2	Left turn signal [19]
3	Right turn signal [18]
4	Power [94]

Figure 3. Connector Locations

1	Screw
2	Base assembly

Figure 4. Standard Tail Lamp

INSTALL

1.	Install turn signals. a. See Figure 5. Apply threadlocker to screws (1).LOCTITE 262 HIGH STRENGTH THREADLOCKER AND SEALANT (RED) (94759-99) b. Install screws (1). Tighten. Torque: 14–17 N·m (10–13 ft-lbs) Turn signal screw c. Route cable (3) as shown through bracket opening. d. Install new cable straps (2).
2.	See Figure 6. Route turn signal wires through gasket (1).
3.	Route turn signal wires through rear fender.
4.	Install turn signal housing (2) and gasket (1) to rear fender. a. Make sure not to pinch any turn signal wires.
5.	Install screw (5). Tighten. Torque: 4.5–5.5 N·m (40–49 in-lbs) Turn signal housing screw
6.	Refer to Table 3. Splice power connector wires [94] to tail lamp wires [93]. See Electrical Diagnostic Manual (EDM).
7.	See Figure 6. Install tail lamp. a. Install tail lamp (3) to turn signal housing (2). b. Install screws (4). Tighten. Torque: 2.3–2.7 N·m (20–24 in-lbs) Tail lamp screw
8.	Remove connectors from turn signal wires. See EDM. a. Label wires accordingly to ease assembly.
9.	See Figure 1. Add extra wire length from harness extension kit (7). a. Measure accordingly. b. Cut wires to length. c. Splice wires according to EDM.
10.	See Figure 7. Route turn signal wires through conduit (2). a. To avoid confusion, feed one set of wires at a time. b. Use fish tape to assist routing of wires.
11.	Install left and right turn signal connectors. See EDM.
12.	See Figure 8. Install both fender support covers (2) to fender supports (1).

1	Screw (2)
2	Cable strap (2)
3	Cable
4	Gasket
5	Connector (2)
6	Turn signal (2)

Figure 5. Turn Signal Assembly

1	Gasket
2	Turn signal housing
3	Tail lamp
4	Screw (2)
5	Screw

Figure 6. Tail Lamp Assembly

1	Power connector (front) [40]
2	Conduit
3	Turn signal wires routing [18 & 19]
4	Power connector (rear) [94]

Figure 7. Under Fender Harness Routing

1	Fender support
2	Cover (2)

Figure 8. Fender Support Cover

Table 3. Tail Lamp Splicing

Power Connector Wires [94]		Domestic Incandescent Tail Lamp [93]	Non-Domestic Incandescent Tail Lamp [93]	LED Tail Lamp [93]
Blue	Splice To	Blue	Orange/White	Blue
Black		Black	Black	Black
Blue with Stripe		Red/Yellow	Red/Yellow	Red/Yellow
Blue (extra wire)⁽¹⁾		Seal off with heat shrink

(1) The two blue wires are on the same circuit and only one needs to be spliced.

COMPLETE

1.	Install rear fender. See service manual.
2.	Install seat. After installing seat, pull up on seat to verify that it is secure. See service manual.
3.	Install main fuse. See service manual.