Front and Rear Axle Guards
941004202022-08-08
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
43000303 (Front), 43000304 (Rear) | Safety Glasses, Torque Wrench, Loctite 243 Blue |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Front and Rear Axle Guards
Table 2. Kit Contents: Front and Rear Axle Guard Kits
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 2 | End cap, cover, axle | 43000305 | |
| 2 | 2 | Spring | 11700067 | |
| 3 | 2 | Nut, lock | Not sold separately | |
| 4 | 2 | Washer | Not sold separately | |
| 5 | 2 | Housing, cover, axle | 43000306 | |
| 6 | 2 | Nut, hex | Not sold separately | |
| 7 | 2 | Spacer | Not sold separately | |
| 8 | 1 | Inner plate, RH | Not sold separately | |
| 9 | 1 | Inner plate, LH | Not sold separately | |
| 10 | 1 | Shaft | Not sold separately | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit.
If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation.
Improper installation of this kit could result in death or serious injury. (00308b)
INSTALL
Front
| 1. | See Figure 2 and Figure 3. Install shaft (10) through front axle mount. | |
| 2. | See Figure 1 and Figure 3. Install left and right inner plates (8,9) onto shaft (10). | |
| 3. | Apply threadlocker to hex nut (6).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) | |
| 4. | Install hex nuts (6). Tighten. Torque: 18 N·m (159.3 in-lbs) | |
| 5. | Install spacer (7), housing (5), washer (4) and lock nut (3) to shaft (10). | |
| 6. | Tighten lock nut (3). Tighten. Torque: 18 N·m (159.3 in-lbs) | |
| 7. | Install spring (2) and end cap (1). | |
| 8. | Repeat steps 2-7 on opposite side. |
Rear
| 1. | See Figure 2 and Figure 4. Install shaft (10) through rear axle mount. | |
| 2. | See Figure 1 and Figure 4. Install left and right inner plates (8,9) onto shaft (10). | |
| 3. | Apply threadlocker to hex nut (6).LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) | |
| 4. | Install hex nut (6). Tighten. Torque: 18 N·m (159.3 in-lbs) | |
| 5. | Install spacer (7), housing (5), washer (4) and lock nut (3) to shaft (10). | |
| 6. | Tighten lock nut (3). Torque: 18 N·m (159.3 in-lbs) | |
| 7. | Install spring (2) and end cap (1). | |
| 8. | Repeat steps 2-7 on opposite side. |
| 1 | Correct |
| 2 | Incorrect |
Figure 2. Shaft Correct/Incorrect Install
| 1 | Cover (2) |
| 2 | Spring (2) |
| 3 | Nut, lock (2) |
| 4 | Washer (2) |
| 5 | Housing (2) |
| 6 | Nut, hex (2) |
| 7 | Spacer (2) |
| 8 | Inner plate, right |
| 10 | Shaft |
Figure 3. Front Axle Cover Kit (Right Side Shown)
| 1 | Cover (2) |
| 2 | Spring (2) |
| 3 | Nut, lock (2) |
| 4 | Washer (2) |
| 5 | Housing (2) |
| 6 | Nut, hex (2) |
| 7 | Spacer (2) |
| 8 | Inner plate, right |
| 10 | Shaft |
Figure 4. Rear Axle Cover Kit (Right Side Shown)