SCREAMIN' EAGLE® HIGH FLOW 68MM THROTTLE BODY
941004492023-03-16
GENERAL INFORMATION
Table 1. General Information
Kit | Suggested Tools | Skill Level(2) |
|---|---|---|
27300194 | Safety Glasses, Torque Wrench |  |
(2) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Screamin' Eagle® High Flow 68mm Throttle Body
Table 2. Kit Contents: Screamin' Eagle® High Flow 68mm Throttle Body
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Throttle body, 68mm | Not sold separately | |
| 2 | 1 | Seal (throttle body to intake manifold) | 27300209 | |
| 3 | 3 | Screw, flange | 10200373 | |
Components mentioned, but not included in kit | |||||
| A | 1 | Fuel rail assembly | ||
| B | 2 | Fuel injector | ||
| C | 1 | Sensor, T-MAP | ||
| D | 2 | Seal, intake | ||
| E | 1 | Intake manifold, Screamin Eagle, High Flow 68 mm | ||
Hardware kit not included in kit | |||||
| F | 1 | Hardware kit (Part No. 91800058) includes: O-rings (4), M6 Allen head screw (3), M5 TORX screw (1) | ||
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
These items are available at your local Harley-Davidson dealership:
- Screamin' Eagle® (SE) High Flow 68mm Intake Manifold kit (Part No. 27300210) is required for this installation.
- SE High Flow Injector kit (Part No. 27400067) are recommended for this installation.
- Digital Technician II (DT II) is required for proper installation of this kit. Contact a Harley-Davidson dealer.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
PREPARE
| 1. | Install SE High Flow 68 mm Intake Manifold. See installation requirements. a. Follow instructions in the intake manifold kit. | |
| 2. | Remove main fuse. See service manual. |
REMOVE
| 1. | Remove Original Equipment (OE) throttle body and seal. Discard components. See service manual. |
INSTALL
NOTE
SE Performance 68mm High Flow Intake Manifold (Part No. 27300210) should already be installed prior to installing throttle body.
| 1. | See Figure 1. Install seal (2). | |
| 2. | Install throttle body (1). | |
| 3. | Install screws (3). Tighten. Torque: 4–6 N·m (35–53 in-lbs) |
COMPLETE
| 1. | Install main fuse. See service manual. |