SCREAMIN EAGLE OHLINS SIDE COVER KIT

941004572023-06-07

GENERAL INFORMATION

Table 1. General Information

Kits	Suggested Tools	Skill Level⁽¹⁾
54000321	Safety Glasses, Torque Wrench

(1) Tightening to torque value or other moderate tools and techniques required

KIT CONTENTS

Figure 1. Kit Contents: Screamin Eagle Ohlins Side Cover Kit

Table 2. Kit Contents: Screamin Eagle Ohlins Side Cover Kit

Verify that all contents are present in the kit before installing or removing items from vehicle.
Item	Qty	Description	Part No.	Notes
1	1	Side cover	61300783
2	1	Washer	6110
3	1	Screw	942
4	1	Bracket, pre-load adjuster	41600213

GENERAL

Models

For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.

Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets

Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.

Installation Requirements

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:

A Harley-Davidson dealer.
H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.

PREPARE

NOTICE

This device is sensitive to electrostatic discharge (ESD). To prevent damage to the device, always touch the motorcycle frame or a grounded surface before handling. (00588c)

1.	Remove seat. See service manual.
2.	Disconnect negative battery cable. See service manual.
3.	Remove and discard right side cover. See service manual.

REMOVE

1.	See Figure 2. If equipped with ABS: Disconnect ABS connector (4).
2.	Remove cable straps (3).
3.	Remove side cover mounting stud (2). Save for later use.
4.	Remove screw (1).
5.	See Figure 3. Remove ABS module (3) with bracket.
6.	Remove screws (2).
7.	Remove and discard bracket (1).

1	Screw
2	Side cover mounting stud
3	Cable strap (2)
4	Connector

Figure 2. ABS Module with Bracket

	ABS Bracket
	Screw (2)
	ABS Module

Figure 3. ABS Bracket

INSTALL

1.	If equipped with ABS: a. See Figure 4. Install new bracket (1) to ABS module. b. Install screws (2). Tighten. Torque: 10.8–13.5 N·m (96–119 in-lbs) c. Install ABS module (3) with bracket. d. See Figure 5. Install screw (1). Tighten. Torque: 10.8–13.5 N·m (96–119 in-lbs) e. Install side cover mounting stud (2). Tighten. Torque: 8.1–10.8 N·m (72–96 in-lbs) f. Install cable straps (3). g. Connect ABS connector (4).
2.	If equipped without ABS: a. See Figure 6. Install new bracket (3). b. Install screw (1). Tighten. Torque: 10.8–13.5 N·m (96–119 in-lbs) c. Install side cover mounting stud (2). Tighten. Torque: 8.1–10.8 N·m (72–96 in-lbs)

1	Pre-load adjuster bracket
2	Screw (2)
3	ABS Module

Figure 4. Bracket WITH ABS Module

1	Screw
2	Side cover mounting stud
3	Cable strap (2)
4	Connector

Figure 5. ABS Module

1	Screw
2	Side cover mounting stud
3	Pre-load adjuster bracket

Figure 6. Bracket WITHOUT ABS Module

COMPLETE

1.	If installing Screamin Eagle Ohlins Rear Suspension kit, do so at this time.
2.	See Figure 1. Install new side cover (1).
3.	Connect negative battery cable. See service manual.
4.	Install seat. See service manual.