SINGLE-SIDED SWINGARM BAG MOUNTING BRACKET
941004852023-01-09
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
90202532 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Single-Sided Swingarm Bag Mounting Bracket
Table 2. Kit Contents: Single-Sided Swingarm Bag Mounting Bracket
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Mounting bracket | Not sold separately | |
| 2 | 4 | Washer, M6 | 10300259 | |
| 3 | 4 | Screw, M6 x 30 mm | 10201369 | |
| 4 | 1 | Protective tape | 11100302 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
- Separate purchase of Classic Saddlebag (Part No. 90202530) or Modern Saddlebag (Part No. 90202531) is required for this installation.
These items are available at your local Harley-Davidson dealership.
PREPARE
| 1. | See Figure 1. Install protective tape (4) on swingarm. a. See Figure 2. Position mounting bracket (1) to front of swingarm. b. Mark location of where to install protective tape. c. Remove mounting bracket (1). d. Clean area with 50/50 distilled water and isopropyl alcohol mix. NOTE Make sure when installing protective tape that it covers the area of mating parts. e. Peel backing from protective tape (2) and install to swingarm. |
| 1 | Mounting bracket |
| 2 | Protective tape |
Figure 2. Mounting Brackets
INSTALL
| 1. | See Figure 3. Position mounting bracket (2) on swingarm. | |
| 2. | See Figure 4. Install washers (2) to screws (1). NOTE To know which set of holes to install the screws (1), reference Isheet from Saddlebag kit. | |
| 3. | Gain access to saddlebag back panel (3). | |
| 4. | Align holes in back panel (3) with mounting bracket. | |
| 5. | Install screws (1). Tighten in crossing pattern. Torque: 5.7–6.3 N·m (50–56 in-lbs) |
| 1 | Saddlebag |
| 2 | Mounting bracket |
Figure 3. Saddlebag Assembly
| 1 | Screw (4) |
| 2 | Washer (4) |
| 3 | Saddlebag back panel |
Figure 4. Install Screws