FAIRING SUPPORT KIT
941004982024-01-23
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
49000274 | Safety Glasses, Torque Wrench |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Fairing Support Kit
Table 2. Kit Contents: Fairing Support Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Fairing support | 47200354 | |
| 2 | 1 | Flange locknut | 7716 | |
| 3 | 2 | Washer, plain | 6703 | |
| 4 | 1 | Screw, socket head | 4069A | |
| 5 | 1 | Screw, socket head | 2708A | |
| 6 | 1 | Washer | 6116 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
REMOVE
| 1. | Remove outer fairing. See service manual. | |
| 2. | See Figure 2. Remove two screws (1) and mounting clamp (2) from fairing support (5). | |
| 3. | Remove and retain screw (3) and washer (4) from stock fairing support. a. Remove stock fairing support. | |
| 4. | Repeat procedure on opposite side. | |
| 5. | Remove two screws that attach the bottom of the stock engine guard to vehicle frame. | |
| 6. | Remove and discard the hex socket screw and washer holding the top of the guard. a. Remove engine guard from frame, taking care not to scratch the finish or paint on the vehicle. |
INSTALL
| 1. | See Figure 3. Hold fairing support assembly in position. | |
| 2. | See Figure 3. Loosely install mid fairing support mount screws (2, 8), flat washers (3, 7) and nut (9) from kit. | |
| 3. | Install side brackets to vehicle with two screws (5) and washers (6) that were removed earlier. | |
| 4. | Tighten upper mid fairing mount screw (8). Torque: 21.6–24.4 N·m (16–18 ft-lbs) Mounting screw | |
| 5. | Tighten lower mid fairing mount screw (2). Torque: 5.4–6.7 N·m (48–59 in-lbs) Mounting screw | |
| 6. | Tighten two side mount screws (5). Torque: 10.8–12.2 N·m (96–108 in-lbs) Mounting screw | |
| 7. | Install outer fairing. See service manual. |
| 1 | Screw (2) |
| 2 | Mounting clamp |
| 3 | Screw |
| 4 | Washer |
| 5 | Fairing support |
Figure 2. Remove Engine Guard
Figure 3.