OVERWATCH THROW-OVER SADDLEBAGS
941005372024-04-30
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) |
|---|---|---|
90202693 | Safety Glasses, Torque Wrench, Isopropyl alcohol |  |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Overwatch Throw-Over Saddlebags
Table 2. Kit Contents: Overwatch Throw-Over Saddlebags
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 2 | Reflector, red | Not sold separately | Order Reflector kit (Part No. 57300436). Includes items 1-4. |
| 2 | 2 | Screw | Not sold separately | |
| 3 | 2 | Reflector plate, outer | Not sold separately | |
| 4 | 2 | Reflector plate, inner | Not sold separately | |
| 5 | 1 | Yoke, Center | Not sold separately | Order Throw-Over Yoke kit (Part No. 90202774). Items include 5-7. |
| 6 | 1 | Yoke, Right | Not sold separately | |
| 7 | 1 | Yoke, Left | Not sold separately | |
| 8 | 1 | Saddlebag, left | 90202773 | |
| 9 | 1 | Transparent paint guard | 90202776 | |
| 10 | 4 | Hook and loop strap | 90202775 | |
| 11 | 1 | Saddlebag, right | 90202773 | |
| 12 | 2 | Inner dry bag | 90202777 | Not shown |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit.
If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation.
Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
- 2022 and later Nightster models: Separate purchase of Overwatch Throw-Over Saddlebag Support kit (Part No. 90202689) is required for installation.
- 2018 and later Softail (FLSL, FXBB, FXBBS, FXST): Separate purchase of Saddlebag Support kit (Part No. 90201777) is required for installation.
- 2006-2017 and later Dyna models: Separate purchase of Saddlebag Support kit (Part No. 91017-10A) is required for installation.
- 2000 and later XL models (except 1200CX, 1200S, 1200T and 2002-03 883R): Separate purchase of Saddlebag Support kit (Part No. 90201324) is required for installation.
These items are available at your local Harley-Davidson dealership.
PREPARE
| 1. | Install reflector. a. If installed, remove inner dry bag. | 
Figure 4. Reflector Assembly | ||||||||||||
| 
Figure 2. Gain Access | |||||||||||||
| 
Figure 3. Mounting Holes | |||||||||||||
| 2. | Install left and right yokes to saddlebags. | |||||||||||||
| 
Figure 5. Install Yoke | |||||||||||||
| 
Figure 6. Velcro Flaps | |||||||||||||
| 
Figure 7. Secure with Snap |
INSTALL
NOTE
See Installation Requirements for saddlebag support.
Saddlebags can be used with or without a passenger seat. Yoke can be installed under or over passenger seat, whichever fits better depending on model and passenger seat setup.
| 1. | If installed, remove passenger seat. | |||||||||||||
| 2. | Install saddlebag. a. See Figure 8. Insert saddlebag support (1) into mesh lining (2). b. Adjust as needed. | |||||||||||||
| 3. | Support saddlebag. | |||||||||||||
| 4. | Install front and rear hook and loop straps (3, 4). | |||||||||||||
| 5. | Repeat procedure on opposite side. | 
Figure 8. Saddlebag Installation | ||||||||||||
| 6. | See Figure 9. Test fit left (1) and right (2) yokes over rear fender. Do not secure straps at this time. a. If there is a gap, install center yoke. b. Velcro center yoke into place. | 
Figure 9. Yoke Installation | ||||||||||||
| 7. | See Figure 1. Test fit transparent paint guard (9) under yoke pieces. a. Mark cutting locations on paint guard. b. Remove yokes pieces from fender area. c. Clean fender area with 50/50 alcohol and water mixture. d. Cut paint guard to fit and install. | |||||||||||||
| 8. | See Figure 10. Install yokes pieces (4, 5)(6 if required) over fender and secure. a. Connect quick-release buckles (1). b. Pull on straps to tighten assembly. c. Secure excess strap (2) in strap bungee (3). | 
Figure 10. Yoke Assembled | ||||||||||||
| 9. | Make overall adjustments as needed. | |||||||||||||
| 10. | Make sure saddlebag assembly is tightly secured to vehicle. a. See Figure 11. Make sure there is adequate saddlebag (1) to exhaust clearance (2). | |||||||||||||
| 11. | If removed, install passenger seat. |
| 1 | Saddlebag |
| 2 | Exhaust |
Figure 11. Exhaust Clearance
GETTING READY FOR TRAVEL
| 1. | See Figure 12. If using dry bag: a. Install dry bag into saddlebag. b. Secure dry bag to saddlebag by using magnetic locks (1, 2). | 
Figure 12. Dry Bag Install | ||||||
| 2. | See Figure 13. Roll up (1) top of bag and insert into saddlebag. | 
Figure 13. Roll Up | ||||||
| 3. | See Figure 14. Secure saddlebag. a. Connect quick-release buckles (1). b. Pull on excess strap (2) to tighten. c. Secure excess strap (2) in strap bungee (3). | 
Figure 14. Secure Saddlebag |
MAINTENANCE
| 1. | Use a lint free cloth to wipe off any dust or dirt. | |
| 2. | Thoroughly clean outer surface with warm water and a mild detergent. | |
| 3. | Do not use artificial means to dry material quickly. | |
| 4. | Contains one or more of the following materials: a. Polyester b. Polypropylene c. Polyethylene d. Polyvinyl chloride |